Design speed is used to establish what?
A Geometric design features
B Concrete mix proportions
C Bridge bearing material
D Roadside paint shade
Answer: A. Geometric design features. Design speed influences curve, sight-distance and related geometric design values.
A ruling gradient is the desirable maximum for what?
A Emergency braking only
B Normal design conditions
C Parking lots
D Bridge deck drainage
Answer: B. Normal design conditions. Ruling gradient is the preferred limiting grade under ordinary design conditions.
Stopping sight distance consists of perception-reaction and what?
A Lane changing travel
B Overtaking distance
C Vehicle braking travel
D Road widening length
Answer: C. Vehicle braking travel. A driver travels during perception-reaction time before braking distance is added.
Overtaking sight distance is important on which facility?
A One-way divided freeway only
B Two-lane two-way road
C Pedestrian path
D Railway siding
Answer: B. Two-lane two-way road. Passing sight distance matters when opposing traffic shares a two-lane roadway.
The superelevation relation balances lateral acceleration with banking and what?
A Side friction
B Pavement thickness
C Road camber only
D Axle spacing
Answer: A. Side friction. For a vehicle on a curve, e plus side-friction factor relates to V squared over 127R in common units.
A transition curve reduces abrupt change in what?
A Roadway length
B Traffic volume
C Pavement temperature
D Centrifugal acceleration
Answer: D. Centrifugal acceleration. Gradually increasing curvature moderates the lateral acceleration change felt by drivers.
Increasing curve radius at fixed speed generally reduces what?
A Lateral acceleration demand
B Sight distance
C Road length
D Drainage flow
Answer: A. Lateral acceleration demand. Lateral acceleration varies with speed squared divided by radius.
A summit curve is convex when viewed from what?
A Road plan
B Pavement surface
C Traffic map
D Side profile
Answer: D. Side profile. A summit or crest curve is a convex vertical curve in the highway profile.
A sag curve is concave in which view?
A Road plan only
B Cross-section only
C Traffic-flow diagram
D Vertical profile
Answer: D. Vertical profile. Sag curves are concave vertical curves joining descending and ascending grades or vice versa.
Headlight sight distance is commonly checked on which curve?
A Crest curve only
B Straight tangent only
C Sag vertical curve
D Horizontal transition only
Answer: C. Sag vertical curve. At night on a sag curve, headlight beam geometry can control available sight distance.
Flexible pavement thickness design depends strongly on traffic and what?
A Road sign height
B Subgrade support
C Signal cycle length
D Parking turnover
Answer: B. Subgrade support. Traffic loading and subgrade strength are central inputs to flexible pavement design.
Repeated axle loading is often represented through what?
A Signal phase units
B Equivalent standard axles
C Passenger trip ends
D Rainfall return periods
Answer: B. Equivalent standard axles. Pavement design converts mixed axle repetitions to an equivalent standard axle measure.
An axle load is carried by which vehicle component?
A Road shoulder
B Traffic island
C Pavement joint
D Wheel assembly axle
Answer: D. Wheel assembly axle. An axle transmits vehicle load to its wheels and pavement contact areas.
Fatigue cracking in bituminous pavement is associated with repeated what?
A Water chlorination
B Signal timing changes
C Tensile strain cycles
D Concrete curing only
Answer: C. Tensile strain cycles. Repeated tensile strains can initiate and propagate fatigue cracking in asphalt layers.
Wheel-path depressions are commonly called what?
A Bleeding
B Ravelling
C Rutting
D Faulting
Answer: C. Rutting. Rutting is a longitudinal depression in wheel paths caused by accumulated deformation.
A pothole is a localized loss of what?
A Roadway alignment
B Pavement material
C Signal visibility
D Shoulder width
Answer: B. Pavement material. Potholes are bowl-shaped surface failures involving loss of pavement material.
Dowel bars at transverse concrete joints mainly transfer what?
A Wheel load across joint
B Longitudinal tension only
C Water pressure
D Traffic signal power
Answer: A. Wheel load across joint. Dowel bars transfer load across a joint while permitting slab movement.
Tie bars across a longitudinal joint mainly resist what?
A Lane separation
B Joint opening at expansion
C Wheel load transfer alone
D Subgrade settlement
Answer: A. Lane separation. Tie bars hold adjacent concrete lanes together and limit joint opening.
A CBR test compares measured penetration load with what?
A Traffic volume
B Concrete cube strength
C Standard penetration load
D Bitumen ductility
Answer: C. Standard penetration load. CBR is the test load divided by a standard load at a specified penetration.
Marshall testing evaluates stability and flow of which material?
A Bituminous mix
B Concrete slab
C Granular subgrade
D Steel reinforcement
Answer: A. Bituminous mix. Marshall mix design testing measures stability and flow under specified loading and temperature.
A bitumen penetration test indicates relative what?
A Consistency or hardness
B Aggregate shape
C Concrete strength
D Soil density
Answer: A. Consistency or hardness. Penetration depth under specified conditions is an empirical measure of binder consistency.
An aggregate abrasion test assesses resistance to what?
A Water absorption only
B Wear and impact
C Traffic signal load
D Soil consolidation
Answer: B. Wear and impact. Abrasion testing evaluates aggregate resistance to wear and impact degradation.
Subgrade compaction is used to improve what?
A Roadside visibility
B Signal coordination
C Pavement color
D Density and support
Answer: D. Density and support. Compaction increases soil density and generally improves support and stability.
Blocked pavement drainage may increase what?
A Design speed
B Sight distance
C Signal capacity
D Moisture damage risk
Answer: D. Moisture damage risk. Poor drainage allows water to weaken layers and accelerate pavement deterioration.
Roadside delineators help drivers recognize what?
A Subgrade strength
B Traffic volume
C Road alignment at night
D Pavement thickness
Answer: C. Road alignment at night. Delineators improve visual guidance by marking roadway alignment, especially in low visibility.