Difficulty: Hard
As liquid fuel temperature rises, what usually happens to its vapor pressure?
A It decreases
B It becomes zero
C It remains fixed
D It increases
Answer: D. It increases. Many fuels have higher vapor pressure at higher temperature, increasing vapor formation risk.
A pump inlet pressure falls below fuel vapor pressure. What can occur?
A Octane rise
B Cavitation
C Injector sealing
D Fuel thickening
Answer: B. Cavitation. Local vapor bubbles can form when inlet pressure falls below fuel vapor pressure.
For reliable pump operation, available NPSH should be what?
A Below vapor pressure
B Equal to zero
C Below required NPSH
D Above required NPSH
Answer: D. Above required NPSH. Available net positive suction head should exceed the pump’s required NPSH.
Why can warm return fuel raise tank vapor generation?
A It heats the tank fuel
B It lowers fuel volatility
C It removes all headspace
D It increases injector pulse
Answer: A. It heats the tank fuel. Hot recirculated fuel can raise tank temperature and promote vapor formation.
Why must air be purged from a diesel supply circuit after service?
A Air raises fuel lubricity
B Air increases cetane quality
C Air compresses and disrupts delivery
D Air cools the injection pump
Answer: C. Air compresses and disrupts delivery. Entrained air is compressible and can prevent stable fuel pressure and injection.
Which device meters fuel entering a common-rail pump?
A Tank level sender
B Inlet metering valve
C Canister purge valve
D Carburetor choke
Answer: B. Inlet metering valve. An inlet metering valve controls how much fuel enters the high-pressure pump.
What does closed-loop rail-pressure control compare?
A Target and measured pressure
B Tank level and road speed
C Injector color and fuel grade
D Coolant pressure and oil level
Answer: A. Target and measured pressure. The controller uses measured rail pressure to track a commanded target.
Why is injector leak-off flow compared across diesel cylinders?
A Measure exhaust oxygen
B Set tire pressure
C Find excessive internal leakage
D Check coolant concentration
Answer: C. Find excessive internal leakage. Unequal or excessive return flow can indicate internal injector leakage.
A leaking injector after shutdown can cause which symptom?
A Higher tire wear
B Lower radiator level
C Rail pressure loss
D Increased wheelbase
Answer: C. Rail pressure loss. Fuel escaping internally can reduce residual rail pressure and impair restart.
Positive short-term fuel trim means the ECU is doing what?
A Removing fuel
B Closing the tank vent
C Retarding the wheels
D Adding fuel
Answer: D. Adding fuel. Positive trim means the ECU is correcting toward a richer mixture by adding fuel.
Negative short-term trim indicates what correction?
A Adding fuel
B Raising pump voltage
C Subtracting fuel
D Opening the throttle fully
Answer: C. Subtracting fuel. Negative trim means the ECU is removing fuel relative to its base command.
What does long-term fuel trim represent?
A Instant tank level
B Fuel rail length
C Learned persistent correction
D Injector nozzle diameter
Answer: C. Learned persistent correction. Long-term trim stores sustained mixture corrections learned over time.
What can an EVAP system pressure test reveal?
A Vapor-system leaks
B Injector coil resistance
C Engine compression ratio
D Wheel bearing play
Answer: A. Vapor-system leaks. Pressure or vacuum testing can identify leaks in the evaporative-emissions system.
A purge valve stuck open at idle can introduce what?
A Extra coolant
B Lubricating oil
C Compressed exhaust only
D Uncontrolled fuel vapor
Answer: D. Uncontrolled fuel vapor. Uncommanded vapor flow can disturb the idle mixture and cause rough running.
A large voltage drop to an electric pump can cause what?
A Higher fuel octane
B More injector cylinders
C Low fuel delivery pressure
D Lower vapor pressure
Answer: C. Low fuel delivery pressure. Reduced pump voltage can lower motor speed and fuel output.
Why might a restricted fuel filter show up under high load?
A Fuel density becomes zero
B Demand exceeds restricted flow
C Tank volume increases
D Injector timing stops
Answer: B. Demand exceeds restricted flow. The restriction may limit flow when the engine demands a high fuel rate.
Pressure falls rapidly after shutdown. What does this test result suggest?
A Correct valve timing
B Leak or failed retention
C High tire pressure
D Low coolant flow
Answer: B. Leak or failed retention. Rapid pressure decay can point to leakage or a failed pressure-retention component.
Why measure fuel pressure under load as well as at idle?
A Set compression ratio
B Expose flow limitations
C Measure tank capacity
D Adjust brake balance
Answer: B. Expose flow limitations. A system may hold static pressure yet fail to maintain it at high fuel demand.
What does a low-pressure transfer stage supply before high-pressure pumping?
A Ignition voltage
B Coolant flow
C Exhaust backpressure
D Steady feed fuel
Answer: D. Steady feed fuel. A transfer stage supplies fuel to the high-pressure pump inlet.
During diagnosis, why test delivered volume at specified pressure?
A Verify flow under operating load
B Measure fuel color only
C Check battery capacity
D Set spark-plug gap
Answer: A. Verify flow under operating load. Pump delivery should be evaluated at the required pressure, not only as unrestricted flow.
A 200 kW engine has BSFC 0.24 kg/kWh, density 0.74 kg/L, four injectors, and 80% duty. Static flow per injector?
A 338 cm³/min
B 270 cm³/min
C 451 cm³/min
D 676 cm³/min
Answer: A. 338 cm³/min. Fuel use=48 kg/h=64.9 L/h=1,081 cm³/min; divide by four and 0.80 to get about 338 cm³/min.
Why is fuel-pump capacity specified with reserve margin?
A Cover peak demand and losses
B Increase tank headspace
C Reduce injector count
D Lower fuel density
Answer: A. Cover peak demand and losses. A reserve accommodates peak demand and losses from voltage, filters, and operating conditions.
A fuel filter’s differential pressure rises sharply with flow. What does that indicate?
A Rising octane
B Growing restriction
C Injector opening fully
D Lower fuel viscosity
Answer: B. Growing restriction. A larger pressure drop at higher flow is consistent with a flow restriction.
Which measurement helps assess a weak in-tank pump?
A Tank color only
B Wheel speed alone
C Spark timing only
D Pressure and flow together
Answer: D. Pressure and flow together. Pressure plus measured delivery flow helps distinguish a weak pump from a restriction.
Why should a running high-pressure diesel line not be loosened for diagnosis?
A Fuel pressure becomes zero
B The tank will empty instantly
C Fuel can penetrate skin
D The engine gains compression
Answer: C. Fuel can penetrate skin. High-pressure fuel jets can penetrate skin and cause severe injury.