Difficulty: Easy & Basic
Which command duration primarily sets injector delivery per event?
A Injector pulse width
B Fuel tank level
C Fuel rail length
D Air filter area
Answer: A. Injector pulse width. For a given injector and pressure, longer pulse width generally delivers more fuel.
What does a rail-pressure sensor report to engine control?
A Fuel pressure
B Coolant acidity
C Intake noise
D Oil viscosity
Answer: A. Fuel pressure. The pressure sensor measures rail pressure for pump and injection control.
Which injector actuator uses a piezoelectric stack?
A Float-bowl injector
B Venturi injector
C Mechanical choke
D Piezo injector
Answer: D. Piezo injector. Piezo stacks change dimension under voltage and can actuate injectors rapidly.
How does a solenoid injector open?
A Coolant expansion
B Magnetic coil force
C Fuel evaporation
D Exhaust pressure only
Answer: B. Magnetic coil force. Current through a coil creates magnetic force that moves the injector valve.
When is sequential port injection timed?
A Near each cylinder’s intake event
B Only during exhaust
C Once per four engine cycles
D At fuel-tank filling
Answer: A. Near each cylinder’s intake event. Sequential systems time each injector to its cylinder’s intake event.
What does multipoint fuel injection provide?
A One injector for all cylinders
B A pump per wheel
C A rail per valve
D An injector per cylinder
Answer: D. An injector per cylinder. Multipoint injection uses a separate injector for each cylinder.
Where is a single-point injector commonly located?
A Inside every cylinder
B Throttle-body housing
C At each exhaust port
D In the fuel tank
Answer: B. Throttle-body housing. Single-point injection places one injector near the throttle body.
In a diesel common-rail system, what raises rail pressure?
A High-pressure pump
B Oil cooler
C Fuel sender
D Exhaust turbine
Answer: A. High-pressure pump. A high-pressure pump compresses fuel for the common rail.
Why does diesel injection require high pressure?
A Increase engine coolant flow
B Reduce tire rolling loss
C Open the exhaust valve
D Atomize fuel into compressed air
Answer: D. Atomize fuel into compressed air. High pressure helps produce fine sprays that penetrate and mix in dense chamber air.
What can water contamination do to precision diesel equipment?
A Raise octane rating
B Promote corrosion and wear
C Improve spray quality
D Increase fuel lubricity
Answer: B. Promote corrosion and wear. Water can corrode or damage high-precision pumps and injector components.
What does a tank vent system prevent as fuel is consumed?
A High tire pressure
B Excessive tank vacuum
C Injector pulse shortening
D Coolant boiling
Answer: B. Excessive tank vacuum. Venting admits air or manages vapor so a vacuum does not build in the tank.
When does an EVAP purge valve route stored vapor?
A Whenever engine is off
B When engine control permits
C Only during refuelling
D Only at full throttle
Answer: B. When engine control permits. The ECU opens the purge valve under suitable operating conditions to burn stored vapor.
How does activated carbon retain fuel vapor?
A Magnetic attraction
B Mechanical filtration
C Chemical combustion
D Adsorption on carbon surface
Answer: D. Adsorption on carbon surface. Vapor molecules adsorb onto the porous carbon surface.
Why does a lambda sensor support closed-loop fueling?
A It measures fuel level
B It times the crankshaft
C It measures exhaust oxygen
D It detects oil pressure
Answer: C. It measures exhaust oxygen. Exhaust oxygen feedback lets the ECU correct mixture toward its target.
For a stoichiometric mixture, lambda is approximately what?
A 0.5
B 1.5
C 2.0
D 1.0
Answer: D. 1.0. Lambda is actual air-fuel ratio divided by stoichiometric ratio; equality gives one.
What condition can promote cavitation at a pump inlet?
A High tank fill level
B Low exhaust temperature
C Low inlet pressure
D High battery charge
Answer: C. Low inlet pressure. Low inlet pressure can let fuel vaporize locally and form collapsing bubbles.
Why can a pump check valve be useful after shutdown?
A Raise tank capacity
B Reduce injector count
C Cool the fuel rail
D Retain line pressure
Answer: D. Retain line pressure. A check valve helps prevent pressure from draining back after the pump stops.
How can an electronic returnless system regulate supply pressure?
A Control pump output
B Change tire pressure
C Open the exhaust valve
D Adjust coolant thermostat
Answer: A. Control pump output. Many returnless systems vary pump operation using pressure feedback.
Why may a manifold-referenced regulator vary rail pressure?
A Keep tank level constant
B Change diesel cetane quality
C Maintain injector pressure difference
D Prevent wheel lock
Answer: C. Maintain injector pressure difference. Referencing manifold pressure helps maintain the pressure drop across the injector.
What does injector duty cycle express?
A Fuel-tank fill percentage
B Pump gear ratio
C Open-time fraction
D Rail temperature range
Answer: C. Open-time fraction. Duty cycle is the fraction of a repeating period that an injector is energized.
In stratified GDI operation, when can fuel be injected?
A Only during exhaust
B Late in compression
C Before the tank pump
D After the exhaust stroke
Answer: B. Late in compression. Late injection can form a locally combustible region near the spark plug at light load.
Why does a common rail buffer pressure pulses?
A It measures throttle angle
B It filters intake air
C It provides shared fuel volume
D It changes compression ratio
Answer: C. It provides shared fuel volume. The rail’s volume helps supply multiple injections and damp pressure fluctuations.
Who usually controls timing in an electronically managed common-rail system?
A Fuel tank sender
B Engine control unit
C Radiator thermostat
D Wheel speed sensor
Answer: B. Engine control unit. The ECU commands injector timing based on operating conditions.
What can a flex-fuel composition sensor estimate?
A Ethanol content
B Fuel tank shape
C Injector coil temperature
D Exhaust backpressure
Answer: A. Ethanol content. Some flex-fuel systems estimate ethanol concentration to adjust fueling and ignition strategy.
During port injection, where is fuel typically aimed?
A At exhaust valve
B Into oil sump
C Near intake valve
D At crankshaft bearing
Answer: C. Near intake valve. Port injectors commonly direct spray toward the intake valve or port.