Terzaghi’s strip-footing equation includes cohesion, surcharge and what term?
A Concrete creep term
B Unit-weight contribution
C Water-content term
D Pile-group term
Answer: B. Unit-weight contribution. The classic equation is cNc + qNq + one-half gamma B N-gamma.
In bearing-capacity analysis, surcharge q at footing level is often what?
A Gamma times embedment depth
B Cohesion divided by width
C Load divided by area
D Water head times length
Answer: A. Gamma times embedment depth. For uniform soil, surcharge is often gamma Df at the base level.
A general shear failure surface typically extends where?
A To ground surface beyond footing
B Only below footing center
C Only along pile shaft
D Inside the footing concrete
Answer: A. To ground surface beyond footing. General shear failure involves distinct slip surfaces reaching the ground near footing edges.
For loose sand, which failure mode is more likely than general shear?
A Brittle tensile failure
B Punching of concrete
C Local shear failure
D Hydraulic jump
Answer: C. Local shear failure. Loose or compressible soils often show local shear with gradual deformation.
For an eccentric footing load, effective width is commonly B minus what?
A Half the footing length
B Two times eccentricity
C Bearing pressure
D Embedment depth
Answer: B. Two times eccentricity. Meyerhof effective-area treatment uses B-prime = B – 2e in the eccentric direction.
The effective-area method adjusts capacity for what load condition?
A Uniform groundwater
B Soil classification
C Eccentric resultant
D Compaction effort
Answer: C. Eccentric resultant. Reducing the effective dimensions accounts for the smaller area carrying eccentric load.
A shape factor in bearing capacity accounts for footing what?
A Concrete strength
B Plan geometry
C Water-table color
D Pile installation noise
Answer: B. Plan geometry. Shape factors modify the ideal strip-footing solution for rectangular, square or circular bases.
A depth factor in bearing capacity reflects footing what?
A Surface roughness only
B Grain roundness
C Water content
D Embedment depth
Answer: D. Embedment depth. Embedment can affect confinement and bearing capacity, represented by depth factors in some methods.
Local shear capacity is often evaluated using reduced what?
A Footing area only
B Water density
C Pile length
D Strength parameters
Answer: D. Strength parameters. Local shear procedures use reduced strength parameters to reflect progressive failure behavior.
Under a footing, primary consolidation settlement occurs as what dissipates?
A Effective stress
B Soil grains
C Excess pore pressure
D Concrete hydration
Answer: C. Excess pore pressure. Loading initially generates excess pore pressure, which dissipates as consolidation proceeds.
Immediate settlement estimates often use elastic modulus and what?
A Liquid limit
B Coefficient of curvature
C Critical gradient
D Poisson ratio
Answer: D. Poisson ratio. Elastic settlement calculations use stiffness and Poisson’s ratio along with geometry and applied pressure.
A mat foundation can reduce differential settlement by increasing what?
A Pore pressure
B Structural continuity
C Soil plasticity
D Column eccentricity
Answer: B. Structural continuity. A stiff continuous mat redistributes loads and can reduce relative movement between supports.
Pile group capacity is not always the sum of individual piles because of what?
A Higher concrete slump
B Lower cap thickness
C Group interaction
D Soil color change
Answer: C. Group interaction. Stress overlap and block failure can alter group resistance and settlement.
In a friction pile, much axial resistance comes from what?
A Shaft resistance
B Toe plate bearing only
C Pile cap friction
D Soil suction only
Answer: A. Shaft resistance. A friction pile mobilizes substantial shear transfer along its embedded length.
A point-bearing pile should terminate in what layer?
A Competent bearing stratum
B Loose surface fill
C Organic topsoil
D Uncontrolled debris
Answer: A. Competent bearing stratum. Point-bearing piles transmit load to a strong layer at or near the pile toe.
Negative skin friction is treated as what in pile design?
A Additional downward load
B Upward resistance
C No axial action
D Lateral soil reaction
Answer: A. Additional downward load. Downdrag increases the axial demand that the pile must safely carry.
A pile cap is commonly designed to transfer force through what action?
A Hydraulic uplift only
B Soil arching only
C Thermal expansion
D Strut-and-tie action
Answer: D. Strut-and-tie action. Pile caps can behave as deep members with compression struts and tension ties.
A well foundation resists bridge loads through a combination of base resistance and what?
A Capillary suction
B Side resistance
C Roof bracing
D Pavement friction
Answer: B. Side resistance. Well foundations mobilize base and side resistance and are checked for stability and settlement.
A retaining structure’s foundation must check sliding, overturning and what?
A Traffic signal timing
B Concrete color
C Bearing capacity
D Soil classification alone
Answer: C. Bearing capacity. Stability checks commonly include sliding, overturning, bearing pressure and settlement.
The middle-third rule avoids what under a rectangular footing?
A Tensile soil pressure
B Uniform compression
C Bearing stress
D Vertical load
Answer: A. Tensile soil pressure. If the resultant stays in the middle third, the linear soil-pressure distribution remains nonnegative.
A footing’s net allowable pressure should satisfy which service check?
A Steel yield strain
B Settlement limit
C Pile driving energy
D Concrete slump range
Answer: B. Settlement limit. A pressure acceptable in shear may still exceed the permitted settlement criterion.
Ground improvement can support shallow foundations by increasing what?
A Water content only
B Column dead load
C Soil stiffness or strength
D Groundwater head
Answer: C. Soil stiffness or strength. Densification, stabilization or reinforcement can improve bearing performance and reduce settlement.
An expansive-soil foundation should account for moisture-driven what?
A Magnetic response
B Thermal conductivity
C Particle color
D Volume change
Answer: D. Volume change. Expansive clays swell and shrink as their moisture state changes.
A plate-load test is least reliable for predicting long-term behavior of what?
A Deep compressible clay layers
B Shallow dense sand
C Thin gravel crust
D Sound rock surface
Answer: A. Deep compressible clay layers. A small plate has limited influence depth and may not represent deep consolidation settlement.
A factor of safety against bearing failure should be applied to what?
A Soil water content
B Footing length only
C Elastic modulus
D Ultimate capacity
Answer: D. Ultimate capacity. The safety factor reduces ultimate resistance to an allowable design capacity.