A site investigation is performed mainly to determine what?
A Concrete curing time
B Rebar color
C Subsurface conditions
D Roof drainage area
Answer: C. Subsurface conditions. Ground investigation identifies soil layers, groundwater and design properties.
Which test commonly provides an in-situ penetration blow count?
A CBR only
B Slump test
C Los Angeles test
D SPT
Answer: D. SPT. The standard penetration test records blows needed to drive a sampler through specified increments.
A CPT commonly reports cone resistance and what?
A Sleeve friction
B Concrete slump
C Pile length
D Plastic limit
Answer: A. Sleeve friction. A cone penetration test measures tip resistance and sleeve friction, often with pore pressure.
Which foundation type spreads many column loads over most of a building footprint?
A Strip footing
B Single pad
C Raft foundation
D Driven pile
Answer: C. Raft foundation. A raft covers a large plan area and supports multiple columns or walls.
A footing near a property boundary may need which arrangement?
A Uniform isolated pads
B Floating slab
C Open caisson
D Combined footing
Answer: D. Combined footing. A combined footing can keep the resultant within the base when a boundary prevents a centered pad.
Gross bearing pressure includes what?
A Only footing self-weight
B Only pore pressure
C Pile shaft friction
D Overburden at foundation level
Answer: D. Overburden at foundation level. Gross pressure is the total contact pressure at the foundation base, including existing overburden effects.
Net foundation pressure subtracts which initial pressure?
A Pile capacity
B Concrete cover
C Overburden pressure
D Groundwater depth
Answer: C. Overburden pressure. Net pressure is gross applied pressure minus the original overburden pressure at foundation level.
A factor of safety against bearing failure compares ultimate capacity with what?
A Applied pressure
B Permeability
C Settlement time
D Water content
Answer: A. Applied pressure. Bearing safety factor is a capacity-to-demand ratio.
Local shear failure is commonly associated with what soil response?
A Sudden brittle rock fracture
B Purely elastic rebound
C Hydraulic piping only
D Progressive yielding
Answer: D. Progressive yielding. Local shear develops progressively, often in loose or compressible soils.
Punching shear in soil involves what failure shape?
A Wide surface heave
B Footing sinks with limited heave
C Horizontal wall sliding
D Uniform compression only
Answer: B. Footing sinks with limited heave. Punching failure is a localized downward penetration with limited ground-surface heave.
A concentric vertical load on a rectangular footing gives what ideal contact pressure?
A Triangular pressure
B Zero edge pressure
C Uniform pressure
D Negative pressure
Answer: C. Uniform pressure. For a rigid footing on uniform linear elastic support with centered axial load, pressure is uniform.
An eccentric load can cause which contact-pressure pattern?
A Constant zero pressure
B Linear variation across base
C Circular wave pattern
D Uniform uplift everywhere
Answer: B. Linear variation across base. Eccentricity shifts the resultant, producing a linear pressure distribution in the elastic model.
For a footing width B, no tensile contact stress requires e to be within what?
A Outer quarter
B Full width
C Half the length
D Middle third
Answer: D. Middle third. For a rectangular base under linear pressure assumptions, e ≤ B/6 keeps the resultant in the middle third.
Increasing footing width generally spreads load over what?
A Smaller bearing area
B Larger soil area
C A deeper column
D No soil area
Answer: B. Larger soil area. A wider base distributes the same load across more contact area, though settlement and capacity must still be checked.
Pile end-bearing resistance acts mainly at which location?
A Pile toe
B Pile head only
C Ground surface
D Pile cap sides
Answer: A. Pile toe. End bearing develops at the pile tip against the supporting soil or rock.
Pile shaft resistance develops along which surface?
A Pile cap top
B Pile-soil interface
C Toe plate only
D Ground surface only
Answer: B. Pile-soil interface. Shaft resistance is mobilized by shear at the pile-soil interface.
A static pile load test measures load against what?
A Soil color
B Pile movement
C Concrete temperature
D Water chemistry
Answer: B. Pile movement. A load test records pile displacement as applied axial or lateral load increases.
Negative skin friction acts on a pile in which direction?
A Upward at the toe
B Downward along shaft
C Sideways only
D Away from soil
Answer: B. Downward along shaft. Settling surrounding soil can drag the pile downward and add a downdrag load.
A pile group may settle more than one pile because of what?
A Overlapping stress zones
B Lower pile count
C No load transfer
D Reduced cap area
Answer: A. Overlapping stress zones. Stress bulbs from nearby piles interact, affecting group settlement.
An under-reamed pile is often selected in expansive soil to resist what?
A Heave and uplift
B Traffic impact
C Wind vibration
D Pavement rutting
Answer: A. Heave and uplift. The enlarged bulb helps anchor the pile against uplift from expansive-soil movement.
A plate load result may not directly scale to a large footing because of what?
A Size effects in soil
B Concrete color change
C Pile cap rotation
D Rebar corrosion
Answer: A. Size effects in soil. Stress distribution and compressibility can vary with foundation size and soil stratification.
The water table close to a footing may alter effective unit weight below it to what?
A Submerged unit weight
B Dry unit weight only
C Steel unit weight
D Zero unit weight
Answer: A. Submerged unit weight. Below groundwater, buoyancy reduces the soil’s effective unit weight.
Foundation settlement compatibility matters because of what risk?
A Higher soil Gs
B Lower permeability
C Structural distortion
D Faster curing
Answer: C. Structural distortion. Differential movements can distort frames, walls and utility connections.
A drilled shaft is constructed mainly by what process?
A Driving a thin sampler
B Rolling a steel plate
C Boring and concreting
D Compacting a surface layer
Answer: C. Boring and concreting. Drilled shafts are formed by excavating a large-diameter hole and placing reinforcement and concrete.
A pile foundation is useful when near-surface soil is what?
A Sound and shallow
B Uniform rock throughout
C Dry and dense only
D Weak or compressible
Answer: D. Weak or compressible. Deep foundations can bypass weak surface layers and reach competent strata or mobilize deeper resistance.