Difficulty: Hard
Why can one micronaire value not separate fineness from maturity?
A Both affect airflow
B Only length affects airflow
C Colour masks fineness
D Crimp sets the reading
Answer: A. Both affect airflow. Micronaire is a composite response affected by both fibre fineness and maturity.
How can bundle strength differ from mean single-fibre strength?
A Single fibres contain dye
B Bundles remove all variation
C Load sharing differs
D Bundle fibres have no length
Answer: C. Load sharing differs. Fibre interactions and load sharing affect bundle results.
Changing tensile gauge length can alter which result?
A Strength distribution
B Moisture regain formula
C Fibre polymer identity
D Cross-section chemistry
Answer: A. Strength distribution. Gauge length changes the tested fibre segment and can affect measured strength statistics.
Two fibres break at equal force; which has higher tenacity?
A Higher linear density
B Lower linear density
C Greater moisture content
D Longer staple only
Answer: B. Lower linear density. At equal breaking force, the lower linear density produces higher force per unit linear density.
The initial modulus comes from which curve feature?
A Initial stress-strain slope
B Maximum fibre length
C Area under curve
D Curve endpoint only
Answer: A. Initial stress-strain slope. Initial modulus is the slope of the initial stress-strain response.
Work to rupture corresponds to what?
A Micronaire reading
B Peak colour value
C Fibre count per gram
D Area under load-extension curve
Answer: D. Area under load-extension curve. Mechanical work to break is represented by the area under the force-extension curve.
With constant mean length, what happens when SD rises?
A CV increases
B CV decreases
C Mean doubles
D Length becomes uniform
Answer: A. CV increases. CV is SD divided by mean; a larger SD raises CV when mean is fixed.
Name the composite airflow measure used for cotton.
A Fibre aspect ratio
B Micronaire
C Staple length
D Single-fibre modulus
Answer: B. Micronaire. Micronaire responds jointly to cotton fibre fineness and maturity.
What is the purpose of moisture conditioning?
A Straighten every crimp
B Reach moisture equilibrium
C Remove all fibre defects
D Increase sample mass permanently
Answer: B. Reach moisture equilibrium. Conditioning brings textile specimens toward equilibrium with a specified atmosphere.
Which denominator distinguishes regain from content?
A Dry versus conditioned mass
B Length versus diameter
C Force versus extension
D Mean versus deviation
Answer: A. Dry versus conditioned mass. Regain uses oven-dry mass; moisture content uses conditioned mass.
Which property can projection microscopy measure?
A Fabric abrasion loss
B Dye bath pH
C Yarn twist direction
D Fibre diameter
Answer: D. Fibre diameter. Projection microscopy measures fibre diameter from an enlarged image.
HVI length analysis uses which specimen form?
A Prepared fibre beard
B Loose staple bale
C Woven fabric strip
D Twisted yarn loop
Answer: A. Prepared fibre beard. Cotton length is measured optically on a prepared fibre beard.
Mean length is 20 mm and upper-half mean is 25 mm. Find uniformity index.
A 45 percent
B 100 percent
C 80 percent
D 125 percent
Answer: C. 80 percent. Uniformity index is mean length divided by upper-half mean length, times 100.
For a dry mass of 50 g at 8% regain, how much water is present?
A 8 g
B 54 g
C 2 g
D 4 g
Answer: D. 4 g. Water mass is 8 percent of the dry mass: 0.08 Γ 50 g.
Four grams of water are in a 54 g conditioned sample. Find moisture content.
A 50 percent
B 7.4 percent
C 8 percent
D 12.5 percent
Answer: B. 7.4 percent. Moisture content is 4 divided by 54, multiplied by 100.
For a fixed fibre material, higher linear density usually means what?
A Shorter molecular chains
B Lower polymer density
C Less fibre mass per length
D Larger cross-section
Answer: D. Larger cross-section. For the same material density, greater mass per length generally means greater cross-sectional area.
If density is fixed, linear density varies with which quantity?
A Crimp frequency only
B Gauge length
C Cross-sectional area
D Fibre colour
Answer: C. Cross-sectional area. Mass per unit length equals material density times cross-sectional area.
What should a fibre report include to describe spread?
A One selected fibre
B Maximum alone
C Colour alone
D Mean and variability
Answer: D. Mean and variability. A mean with a spread measure describes a distribution better than one maximum.
Repeated tests under unchanged conditions estimate what?
A Reproducibility
B Fineness
C Repeatability
D Maturity
Answer: C. Repeatability. Repeatability concerns agreement under the same method, equipment and conditions.
Comparable tests across different laboratories assess what?
A Staple length
B Moisture regain
C Reproducibility
D Repeatability only
Answer: C. Reproducibility. Reproducibility describes agreement across laboratories or changed test conditions.
Reference weights are used to verify what?
A Count cotton neps
B Measure fibre maturity
C Set yarn twist
D Check force calibration
Answer: D. Check force calibration. Reference loads help verify the force-measurement system.
What should happen after a jaw break?
A Report full gauge strength
B Double the specimen length
C Treat result as invalid
D Average without review
Answer: C. Treat result as invalid. A break at the jaw may be caused by clamping damage, so the test is not a valid gauge-section failure.
Because specimen size affects force, which two results should be reported?
A Force measures maturity
B Size affects breaking force
C Both are always identical
D Tenacity measures colour
Answer: B. Size affects breaking force. Breaking force depends on specimen size; tenacity normalizes force by linear density.
Which statistic is most sensitive to a few extreme lengths?
A Lower quartile
B Range
C Median
D Mode
Answer: B. Range. Range uses only the minimum and maximum values.
What does a low short-fibre index generally suggest?
A More trash particles
B Higher moisture regain
C Fewer short fibres
D Lower polymer density
Answer: C. Fewer short fibres. A lower short-fibre index indicates a smaller measured share of short fibres.