Difficulty: Medium
Given 2.5 tex, what mass corresponds to 2,000 m?
A 4 g
B 5 g
C 7.5 g
D 2.5 g
Answer: B. 5 g. A 2.5 tex fibre weighs 2.5 g per 1,000 m, so 2,000 m weighs 5 g.
How much tenacity results from 9 cN break force and 3 dtex?
A 12 cN per dtex
B 2 cN per dtex
C 6 cN per dtex
D 3 cN per dtex
Answer: D. 3 cN per dtex. Tenacity is breaking force divided by linear density.
With 18 g dry mass and 1.8 g water, compute regain.
A 10 percent
B 9 percent
C 11.1 percent
D 20 percent
Answer: A. 10 percent. Regain is 1.8 divided by 18, multiplied by 100.
When 2 g water is present in 25 g conditioned mass, compute moisture content.
A 10 percent
B 12.5 percent
C 8 percent
D 6 percent
Answer: C. 8 percent. Moisture content is water mass divided by conditioned mass.
Starting at 75 mm, a specimen extends 9 mm. Find elongation.
A 15 percent
B 9 percent
C 12 percent
D 11 percent
Answer: C. 12 percent. Elongation is extension divided by original gauge length.
For mean fibre length 30 mm and SD 3 mm, calculate CV.
A 3 percent
B 9 percent
C 10 percent
D 33.3 percent
Answer: C. 10 percent. CV is standard deviation divided by mean, times 100.
Mean length is 18 mm; upper-half mean is 22.5 mm. Find uniformity index.
A 80 percent
B 125 percent
C 140 percent
D 45 percent
Answer: A. 80 percent. Uniformity index equals mean length divided by upper-half mean, multiplied by 100.
What is the median of 12, 14, 20 and 30 mm?
A 19 mm
B 17 mm
C 14 mm
D 20 mm
Answer: B. 17 mm. For four ordered values, median is the average of the middle pair: 17 mm.
In 11, 13, 13 and 17 mm, what is the mode?
A 11 mm
B 15 mm
C 13 mm
D 17 mm
Answer: C. 13 mm. The mode is the most frequently observed value.
Out of 120 fibres, 18 are short. What is their share?
A 18 percent
B 20 percent
C 12 percent
D 15 percent
Answer: D. 15 percent. Eighteen divided by 120, multiplied by 100, equals 15 percent.
Compare 30 mm length with 0.03 mm diameter. What is the aspect ratio?
A 3,000:1
B 100:1
C 300:1
D 1,000:1
Answer: D. 1,000:1. Divide length by diameter using the same units.
If a fibre cross-section is circular with 40 ΞΌm diameter, what is its area?
A 400Ο ΞΌmΒ²
B 200Ο ΞΌmΒ²
C 800Ο ΞΌmΒ²
D 1,600Ο ΞΌmΒ²
Answer: A. 400Ο ΞΌmΒ². Radius is 20 ΞΌm; area is Ο times radius squared.
Selecting only the longest fibres would cause what bias?
A Overestimate mean length
B Overestimate moisture regain
C Underestimate fibre maturity
D Underestimate fibre fineness
Answer: A. Overestimate mean length. Excluding shorter fibres shifts the sample mean upward.
Why draw specimens across several lot increments?
A Reduce gauge length
B Improve representativeness
C Increase fibre crimp
D Change polymer chemistry
Answer: B. Improve representativeness. Sampling different increments better represents variation across a lot.
Two peaks in a length histogram usually indicate what?
A One uniform population
B No short fibres
C Constant fibre diameter
D Two length populations
Answer: D. Two length populations. Two peaks suggest two subpopulations with different length ranges.
Lower short-fibre index values generally indicate what?
A Higher trash content
B Greater moisture content
C More short fibres
D Fewer short fibres
Answer: D. Fewer short fibres. The index estimates the measured share of short fibres.
Can micronaire alone identify exact fibre fineness?
A No, it measures colour
B Yes, it measures diameter
C Yes, it measures length
D No, maturity also affects it
Answer: D. No, maturity also affects it. Micronaire reflects both fineness and maturity, so it is not a unique fineness measure.
Unlike a single-fibre test, a bundle test includes what?
A One isolated polymer chain
B Load sharing effects
C Only colour variation
D No fibre interactions
Answer: B. Load sharing effects. Many fibres share load in a bundle, affecting aggregate strength.
Conditioning fibre specimens mainly reduces which variation?
A Crimp variation
B Moisture-related variation
C Polymer-type variation
D Length-class variation
Answer: B. Moisture-related variation. Moisture-sensitive results become more comparable after conditioning.
Jaw breaks during tensile testing should be treated how?
A Maximum tenacity
B Normal fibre failure
C Invalid gauge result
D Zero elongation
Answer: C. Invalid gauge result. A jaw break may result from clamping damage rather than gauge-section failure.
Between CV values of 6% and 12%, which sample is more uniform?
A CV of 12 percent
B Both are identical
C CV of 6 percent
D Cannot compare CV
Answer: C. CV of 6 percent. Lower CV indicates less relative length variation.
For 12% elongation at a 100 mm gauge length, what extension occurs?
A 12 mm
B 10 mm
C 120 mm
D 8 mm
Answer: A. 12 mm. Extension is 12 percent of 100 mm.
What should accompany a mean when reporting spread?
A Single observation
B Maximum alone
C Colour grade only
D Standard deviation or CV
Answer: D. Standard deviation or CV. Standard deviation or CV summarizes variability around the mean.
At a cotton mill, why use HVI on bale samples?
A Only yarn twist measurement
B Rapid multi-property testing
C Only fabric abrasion testing
D Only dye bath analysis
Answer: B. Rapid multi-property testing. HVI rapidly measures several important cotton fibre properties.
Which method can assess cotton fibre maturity microscopically?
A NaOH swelling method
B Bursting strength test
C Stelometer jaw test
D Wrap-reel method
Answer: A. NaOH swelling method. The Textiles Committee lists the NaOH swelling method for cotton maturity.