Two fabrics use the same yarns and setts, but one is intended to be sheared easily along the bias in a forming operation. Which structural change tends to help?
A Higher yarn bending rigidity
B Fewer interlacements per repeat
C Smaller gaps at all crossings
D More binding points per length
Answer: B. Fewer interlacements per repeat. With comparable yarns and setts, fewer binding points can allow yarns to rotate and shear more easily.
For ideal orthogonal yarn strips with warp cover 0.48 and weft cover 0.35, calculate their combined projected cover.
A 0.830
B 0.662
C 0.168
D 0.520
Answer: B. 0.662. Add both cover fractions and subtract the overlap: 0.48 + 0.35 − 0.48 × 0.35.
Among move numbers 2, 3, 4 and 6, which produces a regular eight-end satin cycle with every position visited?
A 6
B 2
C 4
D 3
Answer: D. 3. The step must be coprime to 8. Of the listed numbers, only 3 can visit every position before repeating.
Fabric weighs 180 g/m² and is 1.0 mm thick. With solid fibre density 1,500 kg/m³ and no other components, what is its bulk void fraction?
A 12%
B 82%
C 90%
D 88%
Answer: D. 88%. The bulk density is 0.180 kg/m² divided by 0.001 m, or 180 kg/m³. The void fraction is 1 − 180/1,500.
Half the total picks in a pile fabric are ground picks. Total sett is 64 picks/cm and each pile motif uses four pile picks. How many complete motifs fit per centimetre?
A 16 motifs
B 32 motifs
C 8 motifs
D 4 motifs
Answer: C. 8 motifs. Half of 64 means 32 pile picks per centimetre. Divide by four picks per motif.
An eight-pick weave repeat and a six-pick colour order both start on pick 1. After how many picks do their starting positions align again?
A 24 picks
B 12 picks
C 14 picks
D 48 picks
Answer: A. 24 picks. The least common multiple of 8 and 6 is 24 picks.
With 30 ends/cm and 20 picks/cm, a twill step moves one end horizontally and two picks vertically. What is its angle from the crosswise direction?
A 18.4°
B 45.0°
C 71.6°
D 56.3°
Answer: C. 71.6°. The horizontal displacement is 1/30 cm and vertical displacement is 2/20 cm. Their ratio is 3, giving arctan(3).
To form pockets using double cloth, where must the two layers remain unstitched?
A Inside each pocket region
B Around all pocket edges
C Throughout the entire fabric
D Only in the backing yarn
Answer: A. Inside each pocket region. The layers are separated within each pocket. Selected joining lines define boundaries and leave any intended opening.
Why is the move number 1 excluded when choosing dispersed binding points for a regular satin?
A It doubles the repeat
B It misses every position
C It leaves no floats
D It makes adjacent bindings
Answer: D. It makes adjacent bindings. A unit step places each binding beside the previous one in the next row, creating a visible diagonal rather than dispersed points.
Warp yarn crimp is 12% based on fabric length. Express contraction as a percentage of the corresponding straightened yarn length.
A 88.00%
B 10.71%
C 13.64%
D 12.00%
Answer: B. 10.71%. For 100 units of fabric, yarn length is 112 units. Contraction is 12/112 × 100%, or 10.71%.
Web area production doubles but mass throughput rises 50%. What happens to areal density?
A It falls by 50%
B It falls by 25%
C It rises by 50%
D It rises by 25%
Answer: B. It falls by 25%. Mass per area scales with mass throughput divided by area throughput. The new ratio is 1.50/2.00 = 0.75.
Assume 30 ends/cm and 24 picks/cm. Warp is 20 tex at 8% crimp. Weft is 25 tex at 4% crimp. Find dry mass per area.
Starting at binding position 1 in a seven-end satin and advancing by 3 cyclically, where is the fourth binding point?
A 7
B 5
C 6
D 3
Answer: D. 3. The sequence starts 1, 4, 7, 3. The fourth position is 3 after wrapping around the seven-position repeat.
To keep projected warp coverage at 0.60 while changing yarn width from 0.20 mm to 0.15 mm, what sett is needed in the strip model?
A 60 ends/cm
B 30 ends/cm
C 25 ends/cm
D 40 ends/cm
Answer: D. 40 ends/cm. Divide 0.60 by 0.15 mm to obtain 4 ends/mm, or 40 ends/cm.
A single ply and double cloth use the same dry yarn mass per square metre. The double cloth is 40% thicker. What is its bulk density relative to the single ply?
A 60.0%
B 140.0%
C 71.4%
D 28.6%
Answer: C. 71.4%. At the same areal mass, bulk density is inversely proportional to thickness. The ratio is 1/1.4 ≈ 0.714.
Under ideal plane shear with no yarn stretch, the warp and weft angle falls from 90° to 60°. For one repeat cell, what is the area ratio?
A 0.866
B 1.155
C 0.500
D 0.750
Answer: A. 0.866. Cell area equals the product of its unchanged side lengths times the sine of their included angle. The ratio is sin(60°)/sin(90°).
Warp uses 24 ends/cm divided equally between two shafts. One shaft is raised throughout an entire pick. What percentage of warp ends are above that pick?
A 4.2%
B 100%
C 25%
D 50%
Answer: D. 50%. Each shaft carries half the ends. Lifting only one shaft places its half above the pick.
Across 160 cm of width, 3,200 needle penetrations occur per stroke. If web advance is 0.8 cm per stroke, find penetration density.
A 40 penetrations/cm²
B 25 penetrations/cm²
C 20 penetrations/cm²
D 2,560 penetrations/cm²
Answer: B. 25 penetrations/cm². One stroke covers an area of 160 × 0.8 = 128 cm². Dividing 3,200 by 128 gives 25 penetrations/cm².
Repeat columns have lift sequences 1100, 0110, 0011, 1001, 1100 and 0011. What is the theoretical minimum shaft count?
A Four
B Six
C Five
D Three
Answer: A. Four. The six columns contain four distinct lift sequences. Each distinct sequence can be assigned one shaft.
During design, which change swaps warp and weft exposure at every existing crossing without changing the yarn path directions?
A Use an extra pile yarn
B Reverse the warp order
C Double both yarn counts
D Invert warp-up crossings
Answer: D. Invert warp-up crossings. Reversing the lift state swaps the yarn system exposed at each crossing while keeping the warp and weft directions fixed.
Diagonal line rises one pick for each end. If warp sett is doubled with pick density fixed, how does its angle from the weft direction change?
A It remains exactly fixed
B It decreases
C It increases
D It becomes negative
Answer: C. It increases. Doubling warp sett halves the horizontal distance per end. With the same vertical rise, the diagonal becomes steeper.
Face and back layers use exactly one face end followed by two back ends in a repeated sequence. Total sett is 54 ends/cm. Find the back sett.
A 36 ends/cm
B 45 ends/cm
C 27 ends/cm
D 18 ends/cm
Answer: A. 36 ends/cm. Two of every three ends belong to the back, giving 54 × 2/3 = 36 ends/cm.
Pick count remains fixed during finishing while the fabric contracts from 102 cm to 96 cm. Starting at 16 picks/cm, find finished pick density.
A 16 picks/cm
B 15 picks/cm
C 17 picks/cm
D 18 picks/cm
Answer: C. 17 picks/cm. There were 102 × 16 = 1,632 picks before finishing. Over 96 cm, the density is 17 picks/cm.
To make a honeycomb design, adjacent areas have longer floats on opposite faces. Which result explains the raised and recessed relief?
A Uneven distribution of floats
B One continuous diagonal
C Fibre melting at crossings
D Constant 1/1 interlacement
Answer: A. Uneven distribution of floats. Long floats in selected regions and firmer interlaced regions produce differences in surface height.
Ignoring binder loss, a dry web weighs 132 g/m² after adding dry binder equal to 10% of its original fibre mass. Find the fibre mass before bonding.
A 118.8 g/m²
B 120 g/m²
C 122 g/m²
D 145.2 g/m²
Answer: B. 120 g/m². The finished dry mass is 1.10 times the fibre mass. Divide 132 by 1.10.