Given a warp-up pattern of 1110 on one end and a one-pick twill step, identify the weave.
A 3/1 warp-faced twill
B 1/3 warp-faced twill
C 2/2 balanced twill
D 3/1 weft-faced satin
Answer: A. 3/1 warp-faced twill. Three raised warp crossings followed by one lowered crossing give a 3/1 warp-faced twill.
Where a double weave is connected along both lengthwise edges but separated internally, what form results?
A Open single cloth
B Pile velvet
C Braided cord
D Tubular cloth
Answer: D. Tubular cloth. Connecting both woven layers at both sides and leaving the interior separate creates a hollow tube.
In a straight draft of 1-2-3-4 repeated, which shaft carries the 15th end?
A Shaft 4
B Shaft 2
C Shaft 3
D Shaft 1
Answer: C. Shaft 3. The 15th end is the third position in the fourth repeat.
Between two otherwise identical plain fabrics, which more readily transmits air under the same pressure difference?
A The more compact fabric
B The thicker yarn package
C Both always transmit equally
D The more open fabric
Answer: D. The more open fabric. Larger and more connected inter-yarn pores usually offer less flow resistance.
Across 96 cm of usable cloth, a repeat occupies 1.5 cm. How many complete repeats fit?
A 48 repeats
B 60 repeats
C 64 repeats
D 144 repeats
Answer: C. 64 repeats. Divide the usable width by the width of one repeat: 96/1.5 = 64.
Straightened yarn measures 84 mm after removal from an 80 mm fabric span. What is its crimp percentage based on fabric length?
A 5%
B 4.76%
C 8%
D 4%
Answer: A. 5%. Crimp is the excess yarn length divided by the fabric length: 4/80 Γ 100%.
Consider two ends that differ at only one pick in the repeat. Can a single shaft reproduce both full sequences?
A Yes, if yarns match
B No, they differ once
C No, unless colour differs
D Yes, if picks match
Answer: B. No, they differ once. One shaft moves all its ends together. A single different lift requires separate shaft control.
Barbed needle penetration density falls when the web advances faster with stroke rate and needle count fixed. Why?
A More penetrations per area
B Fewer penetrations per area
C The fibres necessarily melt
D The needles change gauge
Answer: B. Fewer penetrations per area. The same number of penetrations is spread over more web area per unit time.
Among plain, regular satin and 2/2 twill, which has most frequent yarn interlacement?
A All three are equal
B 2/2 twill
C Plain weave
D Regular satin
Answer: C. Plain weave. Plain alternates above and below at every successive crossing and thus has the most frequent interlacement.
Moving through positions 1, 3, 5, 2 and 4 on a five-position cyclic grid produces which satin move number?
A 1
B 2
C 4
D 3
Answer: B. 2. Add two positions each step, wrapping around after position 5.
Take-down length is 1.2 m and woven width is 1.5 m. If fabric mass is 360 g, find areal density.
A 200 g/mΒ²
B 240 g/mΒ²
C 300 g/mΒ²
D 432 g/mΒ²
Answer: A. 200 g/mΒ². The area is 1.2 Γ 1.5 = 1.8 mΒ². Dividing 360 g by 1.8 mΒ² gives 200 g/mΒ².
For a fabric length of 1.5 m at 18 picks/cm, how many picks are present?
A 1,200 picks
B 270 picks
C 2,700 picks
D 3,000 picks
Answer: C. 2,700 picks. Convert 1.5 m to 150 cm, then multiply by 18 picks/cm.
With four picks in a repeat, the first and third picks require identical lifts. How many different lift patterns can there be at most?
A Two
B Three
C Four
D One
Answer: B. Three. The identical pair contributes one pattern, and each remaining pick can contribute one distinct pattern.
The centreline separation of adjacent yarns is 0.50 mm and their projected widths are both 0.30 mm. What clear gap lies between them?
A 0.50 mm
B 0.80 mm
C 0.20 mm
D 0.30 mm
Answer: C. 0.20 mm. Each yarn occupies 0.15 mm to either side of its centreline. Subtract both half widths from 0.50 mm.
How does an extra-warp figure differ structurally from a warp stripe?
A It replaces every ground pick
B It can stop along length
C It changes yarn direction
D It requires no added yarn
Answer: B. It can stop along length. The supplementary warp can remain hidden where the figure is absent. An ordinary warp stripe extends continuously in the lengthwise direction.
On the current pick, only shafts 1 and 4 rise. Which ends are above it if the draft is 1-2-3-4 for the first four ends?
A Ends 3 and 4
B Ends 1 and 2
C Ends 2 and 3
D Ends 1 and 4
Answer: D. Ends 1 and 4. The draft assigns end 1 to shaft 1 and end 4 to shaft 4, so both ends are lifted.
Find the complete repeat width of eight adjacent ends at a nominal spacing of 0.4 mm per end.
A 2.8 mm
B 20 mm
C 0.05 mm
D 3.2 mm
Answer: D. 3.2 mm. Counting one pitch per end in the repeated pattern gives 8 Γ 0.4 = 3.2 mm.
Thread count across a 3 cm swatch is 81 ends. Find the warp sett.
A 27 ends/cm
B 24 ends/cm
C 30 ends/cm
D 243 ends/cm
Answer: A. 27 ends/cm. Divide 81 ends by the 3 cm counting distance.
Across 10 cm of pile fabric, there are 120 loops in one lengthwise row. What is the mean loop spacing along that row?
A 0.12 mm
B 1.20 mm
C 0.83 mm
D 8.33 mm
Answer: C. 0.83 mm. Divide the row length of 100 mm by 120 equally spaced loop positions.
Suppose two ends have identical warp-up and warp-down sequences throughout the repeat. How may the draft assign them?
A To a separate weft feeder
B To the same shaft
C To opposite sheds always
D To a single warp yarn
Answer: B. To the same shaft. Ends that move together on every pick can be controlled by one shaft.
At 60 ends per inch, approximately what is the equivalent warp sett in ends per centimetre?
A 152.4 ends/cm
B 60.0 ends/cm
C 15.2 ends/cm
D 23.6 ends/cm
Answer: D. 23.6 ends/cm. One inch is 2.54 cm, so divide 60 by 2.54.
How does pronounced fibre alignment affect a nonwoven with otherwise uniform bonding?
A More directional property differences
B Conversion into plain weave
C Identical tensile directions
D Elimination of all pores
Answer: A. More directional property differences. Preferentially aligned fibres usually provide greater tensile resistance along their alignment than across it.
Each layer in a double cloth has 22 ends/cm. What is the total warp sett across both layers?
A 44 ends/cm
B 11 ends/cm
C 484 ends/cm
D 22 ends/cm
Answer: A. 44 ends/cm. The top and bottom layers each contribute 22 ends/cm, so the combined warp sett is 44 ends/cm.
When yarn diameters stay fixed, what happens to projected cover as the thread count rises?
A It generally decreases
B It stays exactly constant
C It becomes zero
D It generally increases
Answer: D. It generally increases. Increasing the number of threads in an area reduces the spaces between them.
In a regular five-end satin, how many single binding points are specified across a repeat?
A Five
B Ten
C One
D Twenty
Answer: A. Five. A regular five-end satin has one isolated binding point per end and per pick.