Difficulty: Hard
On a level road, v = 25 m/s and μ = 0.8. What ideal braking distance is closest?
A 20 m
B 60 m
C 40 m
D 80 m
Answer: C. 40 m. Using d = v²/(2μg) gives 625/(2 × 0.8 × 9.81), approximately 40 m.
A 1,500 kg vehicle travels at 20 m/s. What kinetic energy must braking remove?
A 300 kJ
B 150 kJ
C 600 kJ
D 30 kJ
Answer: A. 300 kJ. Kinetic energy is ½mv² = 0.5 × 1,500 × 20² = 300,000 J.
Mass is 1,600 kg, deceleration 0.6g, CG height 0.55 m, wheelbase 2.75 m. Load transfer is about what?
A 1.88 kN
B 0.94 kN
C 3.76 kN
D 5.89 kN
Answer: A. 1.88 kN. Longitudinal load transfer is ma h/L: 1,600 × 0.6g × 0.55/2.75, approximately 1.88 kN.
A 5:1 pedal ratio receives 120 N input. What pushrod force is ideal?
A 24 N
B 120 N
C 600 N
D 720 N
Answer: C. 600 N. Ignoring losses, pedal leverage multiplies force by five: 5 × 120 = 600 N.
A 20 mm master piston receives 500 N. What hydraulic pressure is closest?
A 0.80 MPa
B 2.50 MPa
C 5.00 MPa
D 1.59 MPa
Answer: D. 1.59 MPa. A 20 mm piston has about 314 mm² area; 500/314 = 1.59 N/mm², or 1.59 MPa.
A floating-caliper piston force is 2 kN. What normal force acts on the outer pad?
A 1 kN
B 4 kN
C 8 kN
D 2 kN
Answer: D. 2 kN. Caliper reaction applies approximately the same normal force to the outer pad as the piston applies inward.
Total pad normal load is 10 kN, μ = 0.4, effective radius 0.12 m. Disc torque is what?
A 480 N·m
B 240 N·m
C 1,200 N·m
D 4,800 N·m
Answer: A. 480 N·m. Brake torque is friction coefficient × total pad normal load × effective radius: 0.4 × 10,000 × 0.12 = 480 N·m.
Wheel torque is 900 N·m and tire radius is 0.30 m. Contact-patch force is what?
A 270 N
B 3,000 N
C 900 N
D 30,000 N
Answer: B. 3,000 N. Longitudinal force equals wheel torque divided by tire radius: 900/0.30 = 3,000 N.
Two 5 kg rotors absorb 300 kJ equally; cp = 500 J/kg·K. Temperature rise is about what?
A 30°C
B 120°C
C 60°C
D 300°C
Answer: C. 60°C. Combined heat capacity is 2 × 5 × 500 = 5,000 J/K; 300,000/5,000 = 60 K.
A 6 kN braking force acts on a 1,200 kg vehicle. Deceleration is what?
A 2 m/s²
B 5 m/s²
C 7.2 m/s²
D 50 m/s²
Answer: B. 5 m/s². Newton’s second law gives deceleration = force/mass = 6,000/1,200 = 5 m/s².
Vehicle speed is 25 m/s and tire peripheral speed is 20 m/s. Braking slip ratio is what?
A 0.20
B 0.10
C 0.25
D 0.80
Answer: A. 0.20. Braking slip ratio is (vehicle speed − wheel peripheral speed)/vehicle speed = 5/25 = 0.20.
A high center of gravity increases braking load transfer through which factor?
A Rotor thickness
B CG height
C Pedal ratio
D Pad area
Answer: B. CG height. For equal mass, deceleration, and wheelbase, load transfer rises in proportion to center-of-gravity height.
A diagonal split circuit loses one hydraulic circuit. What is the design benefit?
A Some wheels retain braking
B All brakes lock together
C ABS gains more pressure
D Pedal force becomes zero
Answer: A. Some wheels retain braking. Separate diagonal circuits allow partial service braking after one circuit fails.
In a four-channel ABS, what can each channel control?
A Engine compression
B Individual wheel pressure
C Spring preload
D Tire diameter
Answer: B. Individual wheel pressure. ABS can modulate wheel-brake pressure to manage different adhesion at individual wheels.
Which condition caps torque reaching the road during a stop?
A Master-cylinder size alone
B Rotor mass alone
C Tire adhesion limit
D Pedal ratio alone
Answer: C. Tire adhesion limit. Even a powerful brake cannot transmit more longitudinal force than the tire-road interface supports.
A brake lining overheats and friction drops. What occurs?
A Thermal fade
B Hydraulic lock
C Wheel hop
D Spring rebound
Answer: A. Thermal fade. Excess lining temperature can reduce friction coefficient and braking effectiveness.
When fluid boils, what can form in a hydraulic brake?
A Extra pad material
B A stronger rotor
C A softer tire
D Compressible vapor
Answer: D. Compressible vapor. Vapor pockets compress under pedal force and prevent full hydraulic pressure from reaching the brakes.
In a long air-brake vehicle, what does a relay valve reduce?
A Wheelbase length
B Application delay
C Compressor speed
D Brake-shoe friction
Answer: B. Application delay. A relay valve uses nearby reservoir air to apply or release distant brakes more quickly.
What does an air-compressor governor control?
A Brake-pad thickness
B Wheel-speed signals
C Spring travel
D Cut-in and cut-out pressure
Answer: D. Cut-in and cut-out pressure. The governor cycles the compressor to maintain system pressure within its operating range.
Under FMCSA guidance, when must visible air warning activate?
A Only after stopping
B At full reservoir pressure
C When pads are new
D Before 60 psi
Answer: D. Before pressure becomes unsafe. FMCSA CDL guidance requires a visible warning before reservoir pressure drops below 60 psi.
What applies a spring brake when system air is lost?
A Stored spring force
B Hydraulic pump pressure
C Wheel-speed signal
D Brake-fluid expansion
Answer: A. Stored spring force. Spring brakes use mechanical spring force for application and air pressure to hold them released.
Why are air-brake reservoirs drained periodically?
A Raise compressor pressure
B Increase brake torque
C Remove water and oil
D Reduce wheel slip
Answer: C. Remove water and oil. Moisture and oil can collect in air tanks and impair operation or cause corrosion.
In an S-cam air brake, what does the slack adjuster connect?
A Rotor to wheel hub
B Pad to caliper piston
C Pushrod to camshaft
D Pedal to master cylinder
Answer: C. Pushrod to camshaft. The slack adjuster transfers brake-chamber pushrod motion to the S-cam shaft.
Why can excessive S-cam brake slack be dangerous?
A Tires gain extra grip
B Air tanks fill faster
C Rotor cooling improves
D Brake application may be delayed
Answer: D. Brake application may be delayed. Excessive clearance requires more actuator travel and can reduce brake effectiveness.
A split-friction stop creates unequal left-right forces. What can ABS help preserve?
A Ride height
B Directional control
C Spring rate
D Engine braking
Answer: B. Directional control. A four-channel ABS can modulate each wheel’s brake pressure separately to manage wheel slip.