Difficulty: Medium
What ultimately limits braking force at the road?
A Brake-pedal travel
B Master-cylinder size alone
C Wheelbase length
D Tire-road adhesion
Answer: D. Tire-road adhesion. The tire-road contact can transmit only a limited force before the tire begins to slide.
During hard braking, where does normal load shift?
A Toward the rear axle
B Only to the left
C Only to the right
D Toward the front axle
Answer: D. Toward the front axle. Deceleration creates a forward load transfer because the vehicleβs center of mass is above the road.
Why are front brakes often sized for greater work?
A Front axle gains braking load
B Front tires are always wider
C Rear wheels rotate faster
D Front rotors are lighter
Answer: A. Front axle gains braking load. Forward load transfer increases the front tiresβ available normal force during braking.
What does the brake pedal lever ratio multiply?
A Brake fluid volume
B Driver input force
C Rotor cooling area
D Tire rolling radius
Answer: B. Driver input force. Pedal leverage increases force applied to the booster or master-cylinder pushrod.
A 300 N push acts on a 300 mmΒ² master piston. What pressure results?
A 0.1 MPa
B 1 MPa
C 3 MPa
D 10 MPa
Answer: B. 1 MPa. Pressure is force divided by area: 300 N / 300 mmΒ² = 1 N/mmΒ², or 1 MPa.
A caliper piston has 500 mmΒ² area at 4 MPa. What piston force results?
A 2,000 N
B 500 N
C 4,000 N
D 8,000 N
Answer: A. 2,000 N. Piston force is pressure times area: 4 N/mmΒ² Γ 500 mmΒ² = 2,000 N.
What mainly determines friction-brake torque at the rotor?
A Wheelbase and spring rate
B Pedal travel and tire width
C Fuel pressure and engine speed
D Pad friction, clamp force, radius
Answer: D. Pad friction, clamp force, radius. Brake torque rises with friction coefficient, normal clamp force, and effective friction radius.
Wheel brake torque divided by tire radius gives what?
A Hydraulic pressure
B Pedal ratio
C Rotor temperature
D Longitudinal tire force
Answer: D. Longitudinal tire force. Ignoring losses, wheel torque divided by rolling radius gives the tractive or braking force at the contact patch.
On a level road, ideal braking distance varies with speed how?
A With speed squared
B Directly with speed
C Inversely with speed
D Independent of speed
Answer: A. With speed squared. For constant deceleration, stopping distance is proportional to the square of initial speed.
How much kinetic energy must a braking vehicle remove?
A Mass times wheelbase
B Force divided by area
C Torque times pedal ratio
D One-half mass times speed squared
Answer: D. One-half mass times speed squared. Vehicle kinetic energy is Β½mvΒ² and must be dissipated or recovered during a stop.
Why can too much rear brake bias be unstable?
A Front tires gain pressure
B Steering ratio increases
C Brake fluid gets colder
D Rear wheels may lock early
Answer: D. Rear wheels may lock early. Rear lockup can reduce directional stability, especially during braking in a turn.
What does a proportioning valve do at high pressure?
A Raises engine vacuum
B Increases pedal ratio
C Limits rear circuit pressure
D Reduces front brake torque
Answer: C. Limits rear circuit pressure. A proportioning function reduces the rate of rear pressure rise above a threshold.
What quantity does ABS actively regulate?
A Brake-pad thickness
B Wheel slip during braking
C Engine torque only
D Vehicle ride height
Answer: B. Wheel slip during braking. ABS uses wheel-speed information to control wheel rotational slip and avoid prolonged lockup.
Vehicle speed is 20 m/s and wheel speed corresponds to 16 m/s. What is braking slip ratio?
A 0.10
B 0.20
C 0.40
D 0.80
Answer: B. 0.20. Braking slip is (vehicle speed β wheel peripheral speed)/vehicle speed: (20β16)/20 = 0.20.
Which ABS action follows detection of impending wheel lock?
A Increase pressure continuously
B Reduce or hold pressure
C Release the pedal linkage
D Change wheel alignment
Answer: B. Reduce or hold pressure. The modulator reduces or holds brake pressure when wheel deceleration indicates impending lock.
What does electronic brake-force distribution adjust?
A Spring preload
B Steering ratio
C Engine compression
D Front-rear brake pressure
Answer: D. Front-rear brake pressure. EBD adapts brake-force distribution to vehicle load and operating conditions.
How can ESC create a corrective yaw moment?
A Change tire diameter
B Open the throttle fully
C Brake selected wheels
D Raise suspension height
Answer: C. Brake selected wheels. Selective wheel braking creates a yaw moment that can counter unwanted vehicle rotation.
A diagonal split hydraulic circuit connects which wheels?
A One front and opposite rear
B Both front wheels only
C Both rear wheels only
D All wheels in series
Answer: A. One front and opposite rear. A diagonal split places one front and the opposite rear wheel in each circuit.
What benefit does a tandem master cylinder provide?
A Automatic pad replacement
B Reduced tire friction
C Separate pressure circuits
D Lower rotor temperature
Answer: C. Separate pressure circuits. Two hydraulic sections allow partial service braking if one circuit fails.
A vacuum booster loses assistance. Which pedal change is likely?
A Less pedal movement always
B Greater pedal effort
C Higher rotor speed
D Reduced wheel load
Answer: B. Greater pedal effort. The hydraulic brakes may still function, but much more driver force is needed.
Why can a drum brake be self-energizing?
A Drum rotation pulls a shoe
B Fluid pressure vanishes
C The rotor cools faster
D The wheel cylinder retracts
Answer: A. Drum rotation pulls a shoe. Rotation can drag a leading shoe into firmer contact with the drum, increasing braking force.
Which process removes heat from a rotating disc?
A Hydraulic pressure storage
B Spring compression
C Convection to airflow
D Tire slip alone
Answer: C. Convection to airflow. Air flowing over and through the rotor transfers heat away by convection.
Why can boiled brake fluid cause pedal loss?
A Pads become thicker
B Rotors expand outward
C Vapor compresses in lines
D Tires gain grip
Answer: C. Vapor compresses in lines. Brake vapor is compressible, so pedal movement may not create adequate pressure at the wheels.
Which condition can reduce pad friction during repeated hard stops?
A Lower vehicle mass
B Shorter wheelbase
C Excessive lining temperature
D Higher tire pressure
Answer: C. Excessive lining temperature. High temperature can reduce friction-material effectiveness and contribute to brake fade.
What does a larger rotor thermal mass generally provide?
A More heat capacity
B More pedal leverage
C Less tire adhesion
D Lower hydraulic pressure
Answer: A. More heat capacity. Greater rotor mass can absorb more heat for a given temperature rise.