How do CAN_H and CAN_L encode a high-speed bus signal?
A Hydraulic pressure
B Optical reflection
C Differential voltage
D Single-ended current only
Answer: C. Differential voltage. High-speed CAN communicates using the voltage difference between its two bus wires.
Which CAN bus state dominates during arbitration?
A Recessive
B Idle only
C Floating
D Dominant
Answer: D. Dominant. ISO 11898 defines the dominant state as prevailing when dominant and recessive bits are driven together.
When two CAN nodes start together, how is bus access resolved?
A Random wire switching
B A central ECU poll
C Mechanical relay timing
D Bitwise nondestructive arbitration
Answer: D. Bitwise nondestructive arbitration. CAN arbitration lets a higher-priority message continue without corrupting the winning frame.
Which CAN message identifier usually has higher priority?
A Higher numerical identifier
B Longest payload
C Latest timestamp
D Lower numerical identifier
Answer: D. Lower numerical identifier. Lower identifier values win arbitration because their bit patterns assert dominant bits earlier.
Why use a twisted CAN wire pair?
A Reduce electromagnetic noise
B Increase battery capacity
C Raise engine torque
D Lower tire pressure
Answer: A. Reduce electromagnetic noise. Twisting helps induced interference affect both conductors similarly, improving differential noise rejection.
Where are high-speed CAN termination resistors normally placed?
A At both bus ends
B At every sensor
C Only inside the battery
D At each ECU ground
Answer: A. At both bus ends. Termination at the two physical ends helps limit signal reflections on the bus.
Two 120 Ω CAN terminators appear in parallel. What resistance is measured across the bus?
A 120 Ω
B 240 Ω
C 60 Ω
D 30 Ω
Answer: C. 60 Ω. Two equal 120 Ω resistors in parallel have an equivalent resistance of 60 Ω.
What is a typical LIN topology?
A Several masters, no slaves
B One master, several slaves
C One sensor, no controller
D Two wires with arbitration
Answer: B. One master, several slaves. LIN uses one master node that controls communication with one or more slave nodes.
Who schedules message headers on a LIN bus?
A Each slave independently
B Battery controller only
C LIN master
D CAN transceiver
Answer: C. LIN master. The LIN master provides frame headers according to a predefined schedule.
Why is LIN often chosen for simple body functions?
A Highest data rate
B Low-cost communication
C Long-range video
D Safety-critical braking only
Answer: B. Low-cost communication. LIN is a low-cost, lower-speed network for simpler sensors and actuators.
What can a vehicle gateway do between networks?
A Route selected messages
B Measure tire pressure
C Control spring rate
D Generate spark voltage
Answer: A. Route selected messages. A gateway passes selected information between network segments with different traffic or protocols.
Why does vehicle multiplexing reduce harness complexity?
A Every signal gets a wire
B Sensors become passive
C Batteries are removed
D Several modules share data lines
Answer: D. Several modules share data lines. Network messages let multiple controllers exchange information over shared communication wiring.
Which memory typically holds ECU program code without power?
A Flash memory
B RAM
C Cache only
D Shift register
Answer: A. Flash memory. Flash is nonvolatile memory commonly used to retain ECU software and calibration data.
Where does an ECU keep temporary calculations while running?
A Flash memory
B RAM
C Fuse element
D CAN termination
Answer: B. RAM. Random-access memory stores temporary working data while the controller is powered.
What can a watchdog timer do if software stops responding?
A Reset the controller
B Change tire pressure
C Open the fuel tank
D Increase bus voltage
Answer: A. Reset the controller. A watchdog expects periodic service from software and can reset a controller after a timeout.
What does freeze-frame data record?
A Conditions near a detected fault
B Every trip for years
C Only battery age
D Tire manufacturing date
Answer: A. Conditions near a detected fault. Freeze-frame data stores selected engine or vehicle conditions associated with a diagnostic event.
Which status do OBD readiness monitors report?
A Suspension ride height
B Brake-pad thickness
C Alternator belt wear
D Emissions test completion
Answer: D. Emissions test completion. Readiness monitors indicate whether supported emissions checks have completed since codes were cleared.
What does the malfunction indicator lamp commonly signal?
A Low windshield washer fluid
B Open door
C Detected emissions-system issue
D Turn signal request
Answer: C. Detected emissions-system issue. OBD systems illuminate the MIL when a qualifying emissions-related fault is detected.
How does a scan tool obtain a stored diagnostic code?
A Reads the tire sidewall
B Requests data from ECU
C Measures exhaust color
D Opens the fuse box
Answer: B. Requests data from ECU. A scan tool communicates with a vehicle controller to request diagnostic information.
What distinguishes a network message from a dedicated wire?
A It carries no information
B It always uses more copper
C It removes all sensors
D Addressed data can be shared
Answer: D. Addressed data can be shared. A network frame can carry data for multiple receiving modules over shared bus wiring.
Why may an ECU compare redundant sensor signals?
A Check plausibility
B Increase wheelbase
C Change fuel octane
D Reduce tire load
Answer: A. Check plausibility. Agreement between related signals can help detect sensor faults or implausible values.
A gateway can isolate which vehicle functions?
A Engine pistons
B Brake pads
C Separate network segments
D Fuel injectors
Answer: C. Separate network segments. Network gateways can control message flow between segments for architecture and security reasons.
What does a controller’s communication transceiver provide?
A Fuel metering
B Wheel alignment
C Bus electrical interface
D Spring damping
Answer: C. Bus electrical interface. A transceiver converts controller logic signals to and from the electrical bus levels.
What is a key benefit of a scheduled LIN bus?
A Random collision handling
B Predictable message timing
C Unlimited data speed
D No master controller
Answer: B. Predictable message timing. Master scheduling provides deterministic timing for the LIN messages in the configured schedule.
Why can an ECU store a pending fault before confirming it?
A Memory is always full
B Fault must recur
C The battery is disconnected
D CAN has no identifiers
Answer: B. Fault criteria may need repeat checks. Some diagnostic strategies require a fault to recur or meet criteria before confirming it and commanding a warning.