Difficulty: Hard
A 3 inΒ² actuator receives 2,000 psi. What output force is produced?
A 3,000 lbf
B 4,500 lbf
C 6,000 lbf
D 9,000 lbf
Answer: C. 6,000 lbf. Force is pressure multiplied by piston area: 2,000 Γ 3 = 6,000 pounds-force.
A 1.5 inΒ² cylinder moves at 4 in/s. What hydraulic flow is closest?
A 1.6 gpm
B 0.8 gpm
C 2.4 gpm
D 3.2 gpm
Answer: A. 1.6 gpm. Flow is area times speed: 6 inΒ³/s, or about 1.56 U.S. gallons per minute.
A 28 V bus supplies a 20 A load. What electrical power is used?
A 280 W
B 420 W
C 840 W
D 560 W
Answer: D. 560 W. Electrical power is voltage times current: 28 Γ 20 = 560 watts.
A 24 V battery rated at 40 Ah stores nominally how much energy?
A 240 Wh
B 960 Wh
C 480 Wh
D 720 Wh
Answer: B. 960 Wh. Nominal energy is voltage times ampere-hours: 24 Γ 40 = 960 watt-hours.
Ignoring drag, a 20,000 kg aircraft at 50 m/s has what kinetic energy?
A 12.5 MJ
B 50 MJ
C 25 MJ
D 100 MJ
Answer: C. 25 MJ. Kinetic energy is one-half mass times speed squared: 0.5 Γ 20,000 Γ 50Β² = 25 million joules.
During ground operation, what should weight-on-wheels logic inhibit?
A Brake cooling
B Fuel transfer
C Cabin ventilation
D Landing-gear retraction
Answer: D. Landing-gear retraction. Ground-sensing logic prevents an unsafe gear retraction command while the aircraft is on its wheels.
A wheel decelerates sharply during braking. What should anti-skid do?
A Reduce brake pressure
B Increase tire pressure
C Retract the gear
D Open fuel crossfeed
Answer: A. Reduce brake pressure. The controller reduces brake pressure on a wheel approaching a skid, then reapplies it as appropriate.
An emergency gear extension is initiated. Which restraint is released first?
A Downlock
B Uplock
C Torque link
D Shimmy damper
Answer: B. Uplock. Releasing the uplock allows the gear to extend by gravity, aerodynamic force, or an emergency mechanism.
Cabin differential reaches its preset maximum. Which device limits further increase?
A Fuel vent
B Hydraulic accumulator
C Bleed check valve
D Positive relief valve
Answer: D. Positive relief valve. The positive-pressure relief valve limits cabin-to-ambient differential pressure.
Outside pressure suddenly exceeds cabin pressure. What protects the fuselage?
A Outflow metering valve
B Fuel crossfeed
C Negative relief valve
D Pitot drain
Answer: C. Negative relief valve. A negative-pressure relief valve admits air to prevent excessive inward differential pressure.
At cruise altitude, how is a lower cabin altitude maintained?
A Regulating cabin outflow
B Opening all vents
C Reducing wing lift
D Increasing tire pressure
Answer: A. Regulating cabin outflow. The pressurization controller maintains cabin pressure by controlling the outflow valve.
A rapid decompression occurs. Which system provides immediate breathing protection?
A Anti-skid
B Oxygen masks
C Ram-air turbine
D Fuel boost pump
Answer: B. Oxygen masks. Passenger and crew oxygen systems supply supplemental oxygen after cabin pressure loss.
Why does cabin pressure not simply match outside pressure at high altitude?
A Fuel tanks seal cabin
B Hydraulic pressure adds air
C Landing gear doors trap air
D Controller limits cabin altitude
Answer: D. Controller limits cabin altitude. The pressurization system maintains a selected cabin pressure schedule within structural limits.
An air-cycle machine produces cooling mainly through what?
A Fuel evaporation
B Electrical resistance
C Air expansion
D Water freezing
Answer: C. Air expansion. Expansion through the air-cycle turbine reduces air temperature for cabin conditioning.
Ice forms on a heated windshield after a heater failure. Which system is affected?
A Hydraulic boost
B Electrical anti-ice
C Fuel crossfeed
D Cabin outflow
Answer: B. Electrical anti-ice. Electrical heating elements provide windshield ice protection on equipped aircraft.
A leading-edge thermal anti-ice system uses what heat source?
A Engine bleed air
B Brake friction
C Battery electrolyte
D Fuel return
Answer: A. Engine bleed air. Hot compressor bleed air can warm protected leading edges and prevent ice accretion.
A brake temperature remains high after landing. What is the best system response?
A Retract landing gear
B Increase brake pressure
C Open cabin outflow
D Allow cooling time
Answer: D. Allow cooling time. Hot brakes require cooling and monitoring because excessive temperature can damage components or create fire risk.
What does a hydraulic accumulator help supply during a brief peak demand?
A Electrical frequency
B Cabin oxygen
C Stored fluid pressure
D Fuel vapor
Answer: C. Stored fluid pressure. The accumulator provides stored hydraulic energy for short-duration demand or damping.
A hydraulic system pressure exceeds its design limit. Which component should relieve it?
A Selector valve
B Relief valve
C Return filter
D Reservoir cap
Answer: B. Relief valve. A pressure relief valve opens at its setting to limit system pressure.
An electrically fired squib is energized. What action follows?
A Gear uplocks engage
B Cabin altitude rises
C Fuel vents close
D Bottle discharges agent
Answer: D. Bottle discharges agent. The squib opens the fire bottle discharge path so extinguishing agent enters the protected zone.
A continuous-loop detector signals excessive heat. What does the crew receive?
A Fire warning
B Low-fuel caution
C Gear unsafe light
D Cabin altitude alert
Answer: A. Fire warning. The fire detection circuit sends a warning when the loop senses an overheat condition.
An inverter fails on a DC-powered aircraft. Which loads are directly affected?
A Hydraulic actuators
B Inverter-fed AC loads
C Fuel tank vents
D Oxygen masks
Answer: B. Inverter-fed AC loads. The inverter’s AC output is lost, affecting loads supplied through that inverter.
The main electrical supply fails but the ram-air turbine deploys. What is its role?
A Fuel transfer
B Cabin cooling
C Emergency power
D Ice removal
Answer: C. Emergency power. The turbine can drive emergency electrical or hydraulic equipment, depending on aircraft design.
Why should overheated brakes be inspected before departure?
A Heat can damage components
B Pressure altitude changes
C Fuel octane drops
D Radio horizon shrinks
Answer: A. Heat can damage components. Excessive brake heat can impair components and increase the risk of fire or tire failure.
A fire bottle is installed for a protected zone. Which signal path usually initiates discharge?
A Pitot-static line
B Squib firing circuit
C Fuel quantity circuit
D Bus-tie sensor
Answer: B. Squib firing circuit. The cockpit discharge command energizes a squib that opens the extinguisher bottle.