Difficulty: Easy & Basic
Which component converts hydraulic pressure into movement?
A Reservoir
B Filter
C Actuator
D Accumulator
Answer: C. Actuator. A hydraulic actuator converts fluid pressure into mechanical motion.
Which valve directs hydraulic flow to a selected component?
A Selector valve
B Check valve
C Relief valve
D Drain valve
Answer: A. Selector valve. A selector valve routes pressurized fluid to the chosen actuator or circuit.
What does a hydraulic filter remove?
A Cabin moisture
B Fuel vapor
C Electrical noise
D Fluid contamination
Answer: D. Fluid contamination. Filters capture particles that could damage pumps, valves, and actuators.
Which gas commonly charges an aircraft hydraulic accumulator?
A Oxygen
B Nitrogen
C Helium
D Carbon dioxide
Answer: B. Nitrogen. Nitrogen is commonly used as the compressible gas charge in an accumulator.
What does a hydraulic relief valve limit?
A Fuel temperature
B Cabin altitude
C System pressure
D Brake wear
Answer: C. System pressure. A relief valve opens above its set point to protect the hydraulic system from excessive pressure.
What does a fuel crossfeed valve allow?
A Drain hydraulic fluid
B Feed from another tank
C Heat engine oil
D Vent cabin air
Answer: B. Feed from another tank. A crossfeed valve lets an engine receive fuel from another tank or side of the system.
Why is an engine fuel boost pump used?
A Supply positive pressure
B Measure fuel quality
C Cool landing brakes
D Pressurize oxygen
Answer: A. Supply positive pressure. A boost pump supplies fuel pressure and can help prevent vapor formation in the feed line.
What does a fuel tank vent prevent?
A Ice on wings
B Brake overheating
C Radio interference
D Pressure imbalance
Answer: D. Pressure imbalance. Tank venting allows air exchange so fuel flow does not create damaging vacuum or pressure.
What does a fuel selector valve choose?
A Fuel supply source
B Hydraulic actuator
C Cabin temperature
D Electrical bus
Answer: A. Fuel supply source. The selector valve directs fuel from the chosen tank or source to the engine.
Where can water and sediment collect for removal from a fuel system?
A Crossfeed valve
B Boost pump
C Sump drain
D Fuel vent
Answer: C. Sump drain. Low-point drains allow trapped water and sediment to be sampled and removed.
Which control can stop fuel flow to an engine?
A Fuel quantity sender
B Fuel shutoff valve
C Tank vent
D Boost pump
Answer: B. Fuel shutoff valve. A shutoff valve isolates the fuel supply when required by the aircraft design or procedure.
What does a fuel quantity sender measure?
A Fuel pressure only
B Engine torque
C Cabin pressure
D Tank fuel level
Answer: D. Tank fuel level. The sender provides a signal used to indicate the amount of fuel in a tank.
What does a continuous-loop fire detector sense?
A Fuel quantity
B Hydraulic flow
C Abnormal heat
D Radio frequency
Answer: C. Abnormal heat. A continuous-loop detector senses excessive temperature along a protected zone.
What releases agent into an engine fire zone?
A Fire bottle
B Pressure regulator
C Fuel vent
D Smoke hood
Answer: A. Fire bottle. The fire bottle contains extinguishing agent that is discharged into the protected zone.
What does a cabin pressure controller command?
A Landing gear position
B Fuel crossfeed
C Brake temperature
D Cabin pressure schedule
Answer: D. Cabin pressure schedule. The controller regulates the pressurization schedule by commanding the outflow system.
A chemical oxygen generator provides what after activation?
A Cabin cooling
B Emergency oxygen
C Hydraulic power
D Radio backup
Answer: B. Emergency oxygen. Chemical generators produce oxygen for passenger masks after activation.
What controls oxygen flow to a user?
A Oxygen regulator
B Pitot valve
C Fuel selector
D Bus tie
Answer: A. Oxygen regulator. An oxygen regulator controls delivery pressure or flow to the user.
What does an air-conditioning pack do?
A Transfer fuel
B Extend landing gear
C Condition cabin air
D Charge brakes
Answer: C. Condition cabin air. Air-conditioning packs cool, heat, and regulate airflow delivered to the cabin.
What can a ram-air turbine provide after power loss?
A Fuel transfer
B Cabin oxygen
C Radio navigation
D Emergency power
Answer: D. Emergency power. A deployed ram-air turbine can drive an emergency hydraulic pump or electrical generator.
What does a transformer rectifier unit produce?
A AC from DC
B DC from AC
C Hydraulic pressure
D Compressed air
Answer: B. DC from AC. A transformer rectifier converts alternating current into direct current.
What does an inverter convert?
A AC into DC
B Fuel into vapor
C DC into AC
D Pressure into heat
Answer: C. DC into AC. An inverter supplies alternating current from a direct-current source.
What does an electrical bus-tie contactor connect?
A Separate buses
B Fuel tanks
C Hydraulic lines
D Oxygen bottles
Answer: A. Separate buses. A bus-tie contactor can connect electrical buses when the system configuration permits.
What is the purpose of an essential bus?
A Power cabin heaters only
B Measure fuel flow
C Control wheel brakes
D Feed critical loads
Answer: D. Feed critical loads. An essential bus supplies selected critical equipment during abnormal electrical configurations.
What does an external power receptacle accept?
A Hydraulic fluid
B Ground electrical power
C Compressed nitrogen
D Fuel from a truck
Answer: B. Ground electrical power. The external power connector allows a suitable ground source to supply aircraft electrical power.
Why may emergency lights have a separate battery?
A Keep lights available
B Increase cabin pressure
C Power the fuel pump
D Heat the pitot tube
Answer: A. Keep lights available. A separate battery can keep emergency lighting available after loss of normal electrical power.