A 2 inΒ² hydraulic piston receives 1,500 psi. What force is produced?
A 1,500 lbf
B 2,500 lbf
C 3,000 lbf
D 4,500 lbf
Answer: C. 3,000 lbf. Hydraulic force equals pressure times piston area: 1,500 Γ 2 = 3,000 pounds-force.
What does a hydraulic selector valve do in an extension cycle?
A Filters return fluid
B Routes fluid to actuator
C Stores nitrogen charge
D Measures wheel speed
Answer: B. Routes fluid to actuator. The selector valve directs pressure and return flow to the selected actuator.
Why can an accumulator reduce hydraulic pump cycling?
A Supplies stored pressure
B Raises fluid temperature
C Filters contaminants
D Measures reservoir level
Answer: A. Supplies stored pressure. Stored hydraulic energy can meet short demands without continuous pump operation.
What input commonly triggers anti-skid pressure reduction?
A Cabin altitude
B Brake pedal position
C Fuel temperature
D Wheel deceleration
Answer: D. Wheel deceleration. Anti-skid control detects an impending wheel skid from wheel-speed changes and modulates pressure.
What does a brake temperature sensor help crews monitor?
A Tire tread depth
B Hydraulic tank level
C Brake heat
D Runway friction
Answer: C. Brake heat. Temperature indications help identify overheated brakes and fire risk.
What confirms that landing gear is down and locked?
A Fuel pressure
B Downlock switches
C Cabin selector
D Pitot heat
Answer: B. Downlock switches. Position switches or sensors provide cockpit indication when the gear reaches its locked position.
A typical emergency extension system first releases what?
A Brake lines
B Fuel vents
C Flap tracks
D Gear uplocks
Answer: D. Gear uplocks. Many emergency systems release the uplocks so gravity or aerodynamic loads can extend the gear.
Why does a weight-on-wheels switch inhibit some gear commands?
A Prevent unsafe ground operation
B Improve radio reception
C Raise cabin pressure
D Balance fuel tanks
Answer: A. Prevent unsafe ground operation. Ground-sensing logic prevents certain airborne or ground-only functions from operating in the wrong condition.
A hydraulic filter bypass opens when what condition occurs?
A Fluid temperature falls
B Reservoir fills
C Filter restriction rises
D Pump speed stops
Answer: C. Filter restriction rises. A bypass can preserve flow if a filter becomes excessively restricted, subject to design limits.
What is the purpose of electrical load shedding?
A Increase generator frequency
B Recharge the fuel tank
C Reduce tire pressure
D Protect essential power
Answer: D. Protect essential power. Load shedding disconnects nonessential loads to preserve power for critical equipment.
What does a generator control unit regulate?
A Cabin oxygen
B Electrical output
C Brake pressure
D Fuel level
Answer: B. Electrical output. The control unit regulates generator voltage and may provide protection and load control.
A transformer rectifier unit supplies which type of output?
A Direct current
B Alternating current
C Hydraulic pressure
D Pneumatic flow
Answer: A. Direct current. The unit converts an AC input into regulated DC for aircraft loads.
Many transport aircraft use which AC frequency?
A 60 Hz
B 200 Hz
C 400 Hz
D 800 Hz
Answer: C. 400 Hz. Aircraft AC systems commonly use 400 Hz to reduce transformer and motor size.
What can an APU supply to an aircraft on the ground?
A Runway guidance
B Wing lift
C Radio bearings
D Electrical power
Answer: D. Electrical power. An auxiliary power unit can drive a generator and supply electrical power on the ground.
How does a cabin pressure controller regulate cabin pressure?
A Changes wing incidence
B Commands outflow valve
C Pumps oxygen directly
D Moves landing gear
Answer: B. Commands outflow valve. The controller schedules cabin pressure by regulating the outflow valve.
Why is cabin climb rate controlled?
A Increase engine thrust
B Prevent brake fade
C Reduce VOR error
D Limit pressure-change rate
Answer: D. Limit pressure-change rate. Controlled pressure change improves comfort and limits abrupt cabin pressure transitions.
What does a positive pressure relief valve prevent?
A Excess cabin differential
B Fuel tank vacuum
C Hydraulic cavitation
D Static-port blockage
Answer: A. Excess cabin differential. The positive relief valve limits cabin pressure above ambient to protect the structure.
What does a negative pressure relief valve prevent?
A Cabin pressure rising
B Fuel flowing backward
C Outside pressure crushing cabin
D Landing gear retracting
Answer: C. Outside pressure crushing cabin. A negative relief valve protects the fuselage if external pressure exceeds cabin pressure.
An air-cycle machine primarily conditions air by what process?
A Fuel atomization
B Expansion and cooling
C Liquid oxygen conversion
D Magnetic induction
Answer: B. Expansion and cooling. The air-cycle machine expands compressed air through a turbine to produce cooling.
What does a heat exchanger remove from hot bleed air?
A Water content only
B Radio noise
C Hydraulic pressure
D Thermal energy
Answer: D. Thermal energy. A heat exchanger transfers heat from bleed air to a cooler airflow.
Thermal wing anti-icing commonly uses what?
A Heated bleed air
B Inflatable boots
C Chemical fluid
D Wheel brakes
Answer: A. Heated bleed air. Hot compressor bleed air can warm protected leading edges to prevent ice formation.
Pneumatic deicing boots operate in what manner?
A Stay heated continuously
B Spray glycol constantly
C Inflate in cycles
D Vibrate the tail
Answer: C. Inflate in cycles. Boots inflate periodically to crack and shed ice from protected surfaces.
What provides electrical windshield anti-icing?
A Fuel crossfeed
B Embedded heating elements
C Hydraulic return
D Oxygen regulator
Answer: B. Embedded heating elements. Electrical resistance elements warm the windshield to prevent or remove ice.
A continuous-loop fire detector responds primarily to what?
A Excessive temperature
B Low fuel pressure
C High cabin humidity
D Radio frequency
Answer: A. Excessive temperature. The detector signals when temperature along the monitored loop exceeds its threshold.
How is a fire extinguisher bottle commonly discharged?
A Hydraulic ram
B Static pressure
C Electrical squib
D Pitot suction
Answer: C. Electrical squib. An electrically fired squib opens the bottle discharge path to release extinguishing agent.