Difficulty: Hard
Given 240 kN axial load and 800 mmΒ² net area, what nominal stress results?
A 30 MPa
B 120 MPa
C 800 MPa
D 300 MPa
Answer: D. 300 MPa. Nominal stress is 240,000 N Γ· 800 mmΒ² = 300 N/mmΒ², or 300 MPa.
At p=0.12 MPa, r=1.25 m, t=5 mm, thin-shell hoop stress?
A 3 MPa
B 30 MPa
C 12 MPa
D 60 MPa
Answer: B. 30 MPa. Thin-cylinder hoop stress is pr/t: 0.12 MPa Γ 1.25 Γ· 0.005 = 30 MPa.
For a 6 kNΒ·m moment and 30 cmΒ³ section modulus, what is the bending stress?
A 20 MPa
B 60 MPa
C 200 MPa
D 600 MPa
Answer: C. 200 MPa. Bending stress is M/S: 6,000 NΒ·m Γ· 30Γ10β»βΆ mΒ³ = 200 MPa.
Pinned column: E=70 GPa, I=1.5Γ10β»βΆ mβ΄, L=1.8 m. Euler load?
A 32 kN
B 320 kN
C 160 kN
D 640 kN
Answer: B. 320 kN. Using ΟΒ²EI/LΒ² gives approximately 320 kN for the ideal pinned column.
Nominal stress is 80 MPa and Kt=2.5. Local peak stress?
A 200 MPa
B 32 MPa
C 80 MPa
D 250 MPa
Answer: A. 200 MPa. Peak elastic stress is Kt times nominal stress: 2.5 Γ 80 MPa = 200 MPa.
At constant stress and geometry, crack length grows fourfold. Stress intensity changes how?
A Quadruples
B Halves
C Doubles
D Unchanged
Answer: C. Doubles. For K proportional to βa, quadrupling crack length doubles stress intensity.
Paris exponent m=3; doubling ΞK multiplies crack-growth rate by?
A Twofold
B Fourfold
C Eightfold
D Sixfold
Answer: C. Eightfold. The Paris relation has rate proportional to ΞKα΅, so 2Β³ gives an eightfold increase.
When a pinned column’s length is halved, how does Euler critical load change?
A Half
B Fourfold
C Double
D Eightfold
Answer: B. Fourfold. Euler load varies as 1/LΒ²; halving length raises ideal critical load by four.
For a thin closed cylinder, longitudinal pressure stress is what fraction of hoop stress?
A One-half
B Equal
C One-quarter
D Double
Answer: A. One-half. Closed-cylinder longitudinal stress is pr/(2t), while hoop stress is pr/t.
In a single-cell wing box, torsional shear flow circulates around what?
A Open edge
B Neutral axis
C Wingtip only
D Closed perimeter
Answer: D. Closed perimeter. A closed thin-walled cell carries circulating shear flow around its perimeter.
Symmetric laminate stacking suppresses which classical coupling?
A Extension-bending
B Lift-thrust
C Pressure-thermal
D Mass-shear
Answer: A. Extension-bending. A symmetric laminate has a zero bending-extension coupling matrix in classical laminate theory.
Balanced Β±45Β° plies reduce which coupling?
A Bending-torsion
B Lift-drag
C Heat-pressure
D Extension-shear
Answer: D. Extension-shear. Balanced angle plies cancel in-plane extension-shear coupling terms.
Under longitudinal tension, which carbon plies carry most load?
A Ninety-degree plies
B Zero-degree plies
C Random plies
D Core cells
Answer: B. Zero-degree plies. Fibers aligned with the longitudinal load carry most of that tensile load.
Impact delamination most directly reduces which composite capability?
A Compression strength
B Thermal conductivity
C Paint adhesion
D Fuel capacity
Answer: A. Compression strength. Delamination can sharply reduce compression-after-impact strength.
In a sandwich panel, failure of the core under transverse load is called?
A Core shear failure
B Face wrinkling
C Rivet tear-out
D Bearing yield
Answer: A. Core shear failure. The low-density core can fail in shear under transverse loading.
Why can eccentric loading threaten a bonded repair?
A Hydrostatic stress
B Thermal flux
C Peel stress
D Pure bearing
Answer: C. Peel stress. Eccentric load transfer can generate peel stresses that open the bond line.
Damage-tolerance inspections aim to find cracks before what?
A Critical size
B First load
C Paint cure
D Retirement
Answer: A. Critical size. Inspection intervals should detect damage before it reaches a structurally critical size.
Safe-life retirement limits remove a part before what is expected?
A Elastic recovery
B Core shear
C Thermal expansion
D Fatigue failure
Answer: D. Fatigue failure. Safe-life limits retire components before fatigue failure is expected within the defined life.
After a crack is found, which capacity must remain adequate?
A Surface gloss
B Thermal conductivity
C Fuel pressure
D Residual strength
Answer: D. Residual strength. The remaining structure must retain adequate strength until the damage is detected and addressed.
Which feature can slow a propagating structural crack?
A Crack arrester
B Sealant bead
C Paint stripe
D Fuel baffle
Answer: A. Crack arrester. Crack arresters or straps can limit crack growth and preserve residual capability.
Compared at equal material area, an open thin section usually has what torsional rigidity?
A Higher rigidity
B Identical rigidity
C Lower rigidity
D Infinite rigidity
Answer: C. Lower rigidity. Closed sections generally resist torsion more efficiently than open sections.
If section moment of inertia doubles at fixed moment and distance, bending stress becomes?
A Double
B Fourfold
C Half
D Unchanged
Answer: C. Half. Because Ο=My/I, doubling I halves elastic bending stress.
Rounded corners around fuselage openings help reduce what?
A Higher cabin pressure
B Lower stress concentration
C Greater wing lift
D Lower fuel flow
Answer: B. Lower stress concentration. Rounded transitions reduce local stress concentration around structural cutouts.
Dissimilar metals in electrical contact with moisture can cause what?
A Creep rupture
B Galvanic corrosion
C Core crushing
D Thermal buckling
Answer: B. Galvanic corrosion. An electrolyte and electrical contact can drive galvanic corrosion between dissimilar metals.
Different thermal expansion in bonded plies can create what after cooling?
A Zero strain
B Lift increase
C Open porosity
D Residual stress
Answer: D. Residual stress. Expansion mismatch during temperature changes can leave residual stresses in bonded laminates.