Difficulty: Easy & Basic
The wing’s principal longitudinal beam is called what?
A Rib
B Stringer
C Fairing
D Spar
Answer: D. Spar. The spar is the principal spanwise beam carrying major wing bending loads.
Ribs chiefly preserve what feature along the wing?
A Airfoil shape
B Cabin pressure
C Engine thrust
D Landing height
Answer: A. Airfoil shape. Ribs maintain the wing’s airfoil contour and support its skin.
What name is given to longitudinal skin stiffeners?
A Ribs
B Frames
C Stringers
D Gussets
Answer: C. Stringers. Stringers stiffen the skin and carry longitudinal loads.
Along a fuselage, which member runs lengthwise?
A Rib
B Longeron
C Bulkhead
D Fairing
Answer: B. Longeron. Longerons are longitudinal fuselage members that help carry axial loads.
In a stressed-skin design, what also carries structural load?
A Outer skin
B Paint coating
C Window seal
D Cabin lining
Answer: A. Outer skin. Stressed skin participates in carrying airframe loads.
Between spar caps, which part mainly carries web shear?
A Wing fairing
B Spar web
C Cabin liner
D Tip fence
Answer: B. Spar web. The web connects the spar caps and carries much of the spar’s shear.
Frames help maintain what fuselage feature?
A Cross-section shape
B Wing sweep
C Propeller pitch
D Tire pressure
Answer: A. Cross-section shape. Fuselage frames support the skin and preserve cross-sectional shape.
During wing bending, spar caps carry what axial actions?
A Heat, moisture
B Lift, drag
C Tension, compression
D Bearing, friction
Answer: C. Tension, compression. Bending places one cap region in tension and the other in compression.
Triangulated members give a truss what?
A Racking resistance
B Cabin insulation
C Surface smoothness
D Fuel capacity
Answer: A. Racking resistance. Triangulation makes a truss resist shape distortion.
Why is a closed wing box valuable?
A Reduces cabin noise
B Raises engine thrust
C Stores landing gear
D Resists torsion
Answer: D. Resists torsion. A closed torque box provides efficient torsional stiffness.
Semi-monocoque construction combines skin with which members?
A Ribs and hinges
B Gears and axles
C Flaps and slats
D Frames and stringers
Answer: D. Frames and stringers. Semi-monocoque structures use stressed skin supported by frames and stringers.
What can a fuselage bulkhead reinforce?
A Fuel spray
B Major sections
C Wingtip flow
D Brake friction
Answer: B. Major sections. Bulkheads reinforce fuselage sections and can transfer loads between them.
Which part mainly streamlines a non-load-bearing gap?
A Spar
B Rib
C Longeron
D Fairing
Answer: D. Fairing. Fairings smooth transitions and are usually not primary load-carrying members.
Fittings chiefly connect what?
A Structural members
B Air parcels
C Fuel droplets
D Control laws
Answer: A. Structural members. Structural fittings join members and transfer loads between them.
Pulling a member apart creates which stress?
A Compression
B Torsion
C Tension
D Bearing
Answer: C. Tension. Tension resists forces that try to pull a member apart.
When a force shortens a member, what stress results?
A Compression
B Tension
C Shear
D Torsion
Answer: A. Compression. Compression resists crushing or shortening forces.
Which stress resists adjacent layers sliding?
A Tension
B Bending
C Bearing
D Shear
Answer: D. Shear. Shear resists forces that make material layers slide relative to one another.
Twisting a wing box produces which stress?
A Torsion
B Compression
C Bearing
D Tension
Answer: A. Torsion. Torsion is the stress associated with twisting.
Bending puts one side in tension and the other in what?
A Shear
B Bearing
C Compression
D Torsion
Answer: C. Compression. Beam bending stretches one side and compresses the opposite side.
Where does landing gear transmit ground reactions?
A Wingtip
B Airframe
C Cabin trim
D Radome paint
Answer: B. Airframe. Landing gear attachments transfer ground loads into the airframe.
Horizontal and vertical stabilizers form which assembly?
A Nacelle
B Empennage
C Wing box
D Fuselage shell
Answer: B. Empennage. The empennage includes the aircraft’s tail surfaces.
What connects the wing, tail, and other major assemblies?
A Fairing
B Radome
C Fuselage
D Winglet
Answer: C. Fuselage. The fuselage is the central body to which major airframe assemblies attach.
Which wing surface forms the contour and shares structural loads?
A Cabin floor
B Wing skin
C Gear door
D Window pane
Answer: B. Wing skin. Wing skin forms the aerodynamic surface and may carry structural loads.
Ribs pass much of the local wing pressure to which members?
A Windows
B Antennas
C Spars
D Fairings
Answer: C. Spars. Ribs help transfer aerodynamic pressure loads to the spars.
Traditional aluminum sheet joints commonly use which fastener?
A O-ring
B Cotter pin
C Cable clamp
D Rivet
Answer: D. Rivet. Rivets are widely used in traditional sheet-metal aircraft structures.