Difficulty: Medium
With a 90 kN tension load over 450 mmΒ², what nominal stress results?
A 20 MPa
B 100 MPa
C 200 MPa
D 450 MPa
Answer: C. 200 MPa. Stress equals load divided by area: 90,000 N Γ· 450 mmΒ² = 200 N/mmΒ².
In elastic beam bending, where is normal stress greatest?
A Outer fibers
B Neutral axis
C Shear center
D Centroid only
Answer: A. Outer fibers. For linear elastic bending, normal stress grows with distance from the neutral axis.
At a beam’s neutral axis, bending normal stress is what?
A Zero
B Maximum tension
C Maximum compression
D Uniformly high
Answer: A. Zero. The bending-stress equation gives zero normal stress at the neutral axis.
Increasing spar depth usually does what to bending stiffness?
A Halves it
B Removes shear
C Increases it
D Leaves it zero
Answer: C. Increases it. Greater section depth can raise the second moment of area and bending stiffness.
Which section property enters elastic bending stress?
A Mass density
B Thermal strain
C Surface roughness
D Second moment of area
Answer: D. Second moment of area. Elastic bending stress depends on moment, distance from the neutral axis, and second moment of area.
Closed wing boxes efficiently resist which load?
A Fuel flow
B Cabin noise
C Torsion
D Thermal expansion
Answer: C. Torsion. Closed thin-walled cells carry torsional shear flow efficiently.
What internal load does a spar web chiefly transmit?
A Transverse shear
B Axial tension only
C Fuel pressure
D Thermal flux
Answer: A. Transverse shear. The spar web transfers transverse shear between the caps.
Euler column buckling load varies with unsupported length how?
A Inverse square
B Directly
C Inverse cube
D Not at all
Answer: A. Inverse square. For an ideal elastic column, critical load is proportional to 1/LΒ².
Rounded cutout corners reduce what?
A Wing loading
B Stress concentration
C Material density
D Cabin pressure
Answer: B. Stress concentration. Smoother transitions reduce local stress concentration at openings.
Which method divides a structure into small elements?
A Fuel metering
B Finite element analysis
C Ray tracing
D Flow visualization
Answer: B. Finite element analysis. Finite element analysis approximates structural response using a discretized model.
Full-scale fatigue tests primarily assess what?
A Paint adhesion
B Fuel economy
C Cyclic durability
D Cabin acoustics
Answer: C. Cyclic durability. Repeated-load testing evaluates structural response over representative load cycles.
After damage, remaining load capacity is called what?
A Residual strength
B Thermal margin
C Surface finish
D Elastic modulus
Answer: A. Residual strength. Residual strength is the capacity remaining after damage is present.
If another path carries required load after one member fails, the structure is?
A Thermally isolated
B Aerodynamically neutral
C Unstressed
D Fail-safe
Answer: D. Fail-safe. Fail-safe arrangements retain adequate capability after a specified failure.
For homogeneous elastic bending, where does the neutral axis pass?
A Shear web
B Centroid
C Wingtip
D Fastener row
Answer: B. Centroid. For a homogeneous section, the neutral axis passes through its centroid.
Which fibers usually carry longitudinal laminate tension?
A Ninety-degree plies
B Random fibers
C Core cells
D Zero-degree plies
Answer: D. Zero-degree plies. Fibers aligned with the load direction carry much of the longitudinal tensile load.
Balanced laminates reduce which coupling?
A Thermal-pressure
B Lift-drag
C Extension-shear
D Mass-volume
Answer: C. Extension-shear. Balanced angle-ply laminates cancel important in-plane extension-shear coupling terms.
Bonded joints distribute load across what?
A A single pin
B A tire tread
C A wingtip
D Adhesive area
Answer: D. Adhesive area. Adhesive bonds transfer load over the bonded area.
Why can peel stress threaten a bonded joint?
A It cools the core
B It raises density
C It removes shear
D It opens the bond
Answer: D. It opens the bond. Peel loads act to separate adherends and can be critical for bonded joints.
Sandwich face sheets carry much of which action?
A Fuel transfer
B Bending
C Combustion
D Bearing friction
Answer: B. Bending. Separated face sheets carry tension and compression from panel bending.
Inside the panel, what stabilizes its faces and carries shear?
A Transverse shear
B Axial thrust
C Fuel vapor
D Lightning current
Answer: A. Transverse shear. The core maintains face separation and carries transverse shear.
Thin-cylinder pressurization creates greatest stress around which direction?
A Circumferential
B Radial only
C Wing spanwise
D Vertical only
Answer: A. Circumferential. For a thin closed cylinder, hoop stress is twice the longitudinal pressure stress.
Crack-growth tracking follows what over service cycles?
A Paint gloss
B Fuel mass
C Crack length
D Wing sweep
Answer: C. Crack length. Fatigue-crack growth analysis tracks crack size as loading cycles accumulate.
In a riveted lap joint, load transfers through what?
A Thermal radiation
B Bearing and shear
C Magnetic flux
D Fuel pressure
Answer: B. Bearing and shear. Rivets transfer load through bearing against joined sheets and shear in the fasteners.
What local response does a strain gauge measure?
A Elastic modulus
B Surface strain
C Air density
D Crack toughness
Answer: B. Surface strain. A bonded strain gauge measures local surface deformation per unit length.
Flutter couples structural motion with what?
A Fuel chemistry
B Ground friction
C Cabin lighting
D Aerodynamic forces
Answer: D. Aerodynamic forces. Flutter is an aeroelastic instability involving interaction between structural motion and aerodynamic forces.