Difficulty: Medium
What does engineering strain compare?
A Load to section area
B Mass to volume
C Stress to density
D Length change to original length
Answer: D. Length change to original length. Engineering strain is change in length divided by original length.
Thin aircraft skins are often analyzed using which assumption?
A Hydrostatic stress
B Plane stress
C Pure torsion
D Rigid-body motion
Answer: B. Plane stress. A thin plate often has negligible stress normal to its surface.
Bearing stress at a fastener hole uses load divided by what?
A Projected contact area
B Wing area
C Fastener length only
D Material density
Answer: A. Projected contact area. Bearing stress uses load divided by fastener diameter times material thickness.
A fastener hole reduces which tensile area?
A Gross wing area
B Bondline area
C Net section
D Surface coating
Answer: C. Net section. The net section is the remaining cross-sectional area after accounting for the hole.
Adhesive joints transfer load mainly through which stress?
A Hydrostatic pressure
B Magnetic stress
C Thermal strain
D Shear stress
Answer: D. Shear stress. Adhesive bonds commonly transfer load through shear across the bondline.
When bonded materials expand differently, what may develop?
A Thermal stress
B Lower density
C Fuel cavitation
D Zero strain
Answer: A. Thermal stress. Expansion mismatch constrained by a joint creates thermal stress.
Why are surface coatings used on aircraft metals?
A To increase fuel flow
B To limit corrosion
C To change wing camber
D To stop elastic strain
Answer: B. To limit corrosion. Protective coatings isolate metal from corrosive environments.
Miner’s cumulative damage estimate reaches failure near what sum?
A Zero
B Ten
C One
D One hundred
Answer: C. One. The linear damage rule often estimates failure when cycle fractions sum to about one.
What does damage-tolerance design require?
A No inspection access
B Infinite material strength
C No fatigue loads
D Detectable flaws with inspection
Answer: D. Detectable flaws with inspection. Damage-tolerance design assumes flaws may exist and manages them through inspection and repair.
How does a fastener hole affect local stress?
A Raises stress concentration
B Eliminates tensile stress
C Lowers all material strength
D Stops crack growth
Answer: A. Raises stress concentration. A geometric discontinuity such as a hole concentrates local stress.
What does a composite’s matrix protect and support?
A Landing gear tires
B Fuel pumps
C Reinforcement fibers
D Metal fasteners only
Answer: C. Reinforcement fibers. The matrix binds, supports, and protects the reinforcement.
Why use a sandwich panel in a wing?
A High mass, low stiffness
B High bending stiffness, low mass
C No core shear
D Zero impact sensitivity
Answer: B. High bending stiffness, low mass. Separated face sheets and a light core provide efficient bending stiffness.
CFRP touching aluminum can create what risk?
A Creep-free operation
B Thermal immunity
C No electrical path
D Galvanic corrosion
Answer: D. Galvanic corrosion. Carbon composites can promote galvanic attack of aluminum when electrically coupled in moisture.
Which nondestructive method can reveal internal delamination?
A Visual color check
B Hardness file
C Ultrasonic inspection
D Surface wipe
Answer: C. Ultrasonic inspection. Ultrasonic methods can detect internal delamination and bond defects.
What does fracture toughness KIC characterize?
A Resistance to crack extension
B Elastic modulus
C Yield strain only
D Surface hardness
Answer: A. Resistance to crack extension. KIC is a material’s plane-strain fracture toughness under defined conditions.
Why inspect fatigue-critical fastener holes?
A Holes stop all fatigue
B Cracks may initiate there
C They remove applied loads
D They prevent corrosion
Answer: B. Cracks may initiate there. Stress concentration around holes makes them common fatigue crack initiation sites.
What is a residual stress?
A Stress from current wind only
B A density measurement
C A surface coating
D Stress remaining without external load
Answer: D. Stress remaining without external load. Residual stress remains in a component after manufacturing or processing.
A bonded repair can reduce drilling through what?
A Paint only
B Fuel lines
C Primary laminate fibers
D Landing tires
Answer: C. Primary laminate fibers. Bonded repairs can avoid additional fastener holes through composite fibers.
Which material direction often carries maximum unidirectional-fiber strength?
A Along the fibers
B Across the fibers
C Through the thickness
D At random angles
Answer: A. Along the fibers. Unidirectional composites are strongest and stiffest along their fibers.
How can a crack grow under cyclic loading?
A By static density
B By repeated stress intensity
C By color fading
D By airflow alone
Answer: B. By repeated stress intensity. Repeated loading can extend a crack through fatigue crack growth.
What is a benefit of a fail-safe structure?
A Every crack is harmless
B Inspection is unnecessary
C Weight becomes zero
D Load can redistribute after damage
Answer: D. Load can redistribute after damage. Fail-safe design provides alternate load paths after a local structural failure.
Why are composite fastener holes carefully inspected?
A Holes increase fiber strength
B Drilling may damage fibers
C They eliminate delamination
D They reduce all bearing loads
Answer: B. Drilling may damage fibers. Drilling can cause fiber breakout, delamination, or other local damage.
What is the purpose of corrosion inhibitor?
A Increase thermal expansion
B Raise tensile strain
C Slow electrochemical attack
D Reduce composite stiffness
Answer: C. Slow electrochemical attack. Corrosion inhibitors reduce the rate of corrosive reactions.
A material’s Poisson ratio relates axial strain to what?
A Lateral strain
B Mass flow
C Thermal conductivity
D Fracture toughness
Answer: A. Lateral strain. Poisson ratio relates transverse strain to axial strain under uniaxial loading.
What property quantifies energy absorption before fracture?
A Hardness
B Toughness
C Density
D Conductivity
Answer: B. Toughness. Toughness measures energy absorbed before fracture.