In a coordinated level turn at 60° bank, what load factor results?
A 1.0
B 1.5
C 2.0
D 3.0
Answer: C. 2.0. Load factor equals 1/cos(bank angle). At 60°, cosine is 0.5, so the factor is 2.
A wing produces lift at q=500 Pa, S=20 m² and CL=1.2. What lift is produced?
A 12 kN
B 8 kN
C 10 kN
D 15 kN
Answer: A. 12 kN. Lift equals dynamic pressure times wing area times lift coefficient: 500 × 20 × 1.2 = 12,000 N.
At 255 m/s in air where sound speed is 340 m/s, what is Mach number?
A 0.65
B 0.85
C 0.95
D 0.75
Answer: D. 0.75. Mach number is true airspeed divided by local speed of sound: 255/340 = 0.75.
For CL=0.8, AR=8 and span efficiency e=0.8, estimate induced drag coefficient.
A 0.016
B 0.032
C 0.024
D 0.064
Answer: B. 0.032. Using CDi = CL²/(πAR e) gives 0.64/(π × 8 × 0.8), about 0.032.
A 60 kN aircraft has 20 m² of wing area. What is its wing loading?
A 1,500 N/m²
B 2,000 N/m²
C 3,000 N/m²
D 4,000 N/m²
Answer: C. 3,000 N/m². Wing loading is weight divided by wing area: 60,000/20 = 3,000 N/m².
The neutral point is at 0.45c and the CG at 0.33c. What is static margin?
A 8% chord
B 12% chord
C 10% chord
D 15% chord
Answer: B. 12% chord. Static margin is neutral-point position minus CG position, expressed as a fraction of mean aerodynamic chord.
At a load factor of 4, how does stall speed compare with 1-g stall speed?
A 2 times
B 1.5 times
C 3 times
D 4 times
Answer: A. 2 times. Stall speed varies with the square root of load factor. The ratio is √4 = 2.
For W=9 kN, ρ=1.225 kg/m³, S=18 m² and CLmax=1.5, estimate stall speed.
A 18.0 m/s
B 28.5 m/s
C 33.0 m/s
D 23.3 m/s
Answer: D. 23.3 m/s. From lift equal to weight, Vs = √(2W/(ρSCLmax)), which is about 23.3 m/s.
On the V–n diagram, positive maneuvering speed occurs where which limits meet?
A Drag and thrust
B Flutter and buffet
C Stall and limit load
D Cruise and descent
Answer: C. Stall and limit load. The positive maneuvering point is the intersection of the positive stall boundary and positive limit-load line.
With a 3.8 limit load factor and a 1.5 ultimate factor, what ultimate factor applies?
A 5.7
B 4.8
C 5.2
D 6.3
Answer: A. 5.7. Ultimate structural load is 1.5 times limit load: 3.8 × 1.5 = 5.7.
A wing has span 24 m and area 72 m². What is its aspect ratio?
A 6
B 8
C 7
D 9
Answer: B. 8. Aspect ratio is span squared divided by wing area: 24²/72 = 8.
A tapered wing has root chord 4 m and taper ratio 0.35. What is tip chord?
A 1.0 m
B 1.8 m
C 2.2 m
D 1.4 m
Answer: D. 1.4 m. Taper ratio is tip chord divided by root chord, so 0.35 × 4 = 1.4 m.
Why does wing sweep delay compressibility effects at a given Mach number?
A It raises air density
B It removes lift
C It lowers normal Mach
D It lowers wing area
Answer: C. It lowers normal Mach. Sweep reduces the velocity component normal to the leading edge, delaying local sonic flow and drag rise.
Which planform feature generally improves lateral static stability?
A Dihedral
B Anhedral
C Wash-in
D Forward sweep
Answer: A. Dihedral. Dihedral creates a restoring rolling tendency after a sideslip, contributing to lateral static stability.
Why can a highly stalled wing create deep-stall risk on a T-tail aircraft?
A Nose gear unloads
B Wake blankets tail
C Wing area grows
D Rudder locks
Answer: B. Wake blankets tail. At high angle of attack, separated wing wake can blanket the high-mounted tail and reduce its pitch-control authority.
What must flutter clearance demonstrate for a certified design envelope?
A Flutter below cruise
B No damping at VA
C Resonance at takeoff
D Adequate margin through VD
Answer: D. Adequate margin through VD. The structure must remain free of aeroelastic instability through the required design speed envelope, with prescribed margins.
Which wing structure primarily carries spanwise bending loads?
A Cabin floor
B Fairing skin
C Spar caps
D Antenna mast
Answer: C. Spar caps. Upper and lower spar caps carry the tension and compression couple created by wing bending.
A thin pressurized fuselage has p=50 kPa, radius 2 m and skin thickness 0.01 m. Estimate hoop stress.
A 5 MPa
B 10 MPa
C 15 MPa
D 20 MPa
Answer: B. 10 MPa. Thin-cylinder hoop stress is pr/t: 50,000 × 2 / 0.01 = 10 million Pa, or 10 MPa.
Using CD=CD0+kCL², find CD for CD0=0.025, k=0.045 and CL=0.8.
What is the main aerodynamic effect of deploying a conventional flap?
A Lower wing area
B Lower profile drag
C Lower stall angle
D Higher maximum lift
Answer: D. Higher maximum lift. Flaps increase wing camber and usually raise maximum lift coefficient, while also adding drag.
For positive maneuver limits, what does the V–n envelope combine?
A Thrust and fuel limits
B Cabin and gear limits
C Stall and structural limits
D Brake and tire limits
Answer: C. Stall and structural limits. The maneuver envelope is bounded by aerodynamic stall at lower speeds and structural load limits at higher speeds.
Moving the CG aft, with the neutral point fixed, does what to longitudinal static margin?
A Decreases it
B Increases it
C Keeps it fixed
D Makes it infinite
Answer: A. Decreases it. Static margin is the distance from CG to neutral point; moving CG aft reduces that distance and stability margin.
Why is washout often built into a wing?
A Increase tip loading
B Delay tip stall
C Raise root stall
D Remove induced drag
Answer: B. Delay tip stall. Washout lowers the tip’s geometric incidence so the root tends to reach stall before the tip.
With St=4 m², tail arm=5 m, S=40 m² and mean chord=2.5 m, find horizontal tail volume coefficient.
A 0.10
B 0.15
C 0.25
D 0.20
Answer: D. 0.20. Horizontal tail volume is St times tail arm divided by wing area times mean chord: 20/100 = 0.20.
At the balanced V1 condition, what relationship holds between accelerate-stop and accelerate-go distances?
A Stop distance doubles
B They are equal
C Go distance doubles
D Neither is defined
Answer: B. They are equal. A balanced field condition selects V1 so accelerate-stop and accelerate-go distances are equal for the defined case.