Difficulty: Medium
The lift equation varies with airspeed squared and what?
A Cabin volume
B Air density
C Fuel grade
D Paint thickness
Answer: B. Air density. Lift equals one-half density times speed squared, area, and lift coefficient.
Which drag component rises with lift at low speed?
A Skin friction
B Form drag
C Wave drag
D Induced drag
Answer: D. Induced drag. Induced drag increases with lift and is significant at lower speeds.
What does a drag polar relate?
A Lift and drag coefficients
B Weight and fuel
C Speed and altitude
D Thrust and temperature
Answer: A. Lift and drag coefficients. A drag polar describes drag coefficient as a function of lift coefficient.
A higher load factor increases which structural demand?
A Cabin volume
B Fuel density
C Wing bending loads
D Tail clearance
Answer: C. Wing bending loads. Higher maneuver load factors increase aerodynamic and structural loads.
In a coordinated level turn, load factor depends on what?
A Paint area
B Bank angle
C Fuel temperature
D Landing gear
Answer: B. Bank angle. For a coordinated level turn, load factor rises as bank angle increases.
Stall speed at load factor n scales approximately with what?
A n squared
B One over n
C Square root of n
D Wing span
Answer: C. Square root of n. Stall speed increases approximately with the square root of load factor.
Which design document maps speed against load factor?
A Drag polar
B Weight chart
C Stability curve
D V-n diagram
Answer: D. V-n diagram. The V-n diagram shows structural load factor limits across airspeed.
What does static margin measure?
A CG versus neutral point
B Wing area to span
C Thrust compared with drag
D Fuel load to payload
Answer: A. CG versus neutral point. Static margin is the distance between the neutral point and CG, normalized by mean aerodynamic chord.
Moving CG forward generally increases which requirement?
A Wing aspect ratio
B Elevator trim force
C Fuel density
D Rudder area
Answer: B. Elevator trim force. A forward CG usually requires greater tail downforce and elevator trim.
The neutral point is associated with what stability boundary?
A Neutral longitudinal stability
B Maximum lift
C Directional control
D Ground clearance
Answer: A. Neutral longitudinal stability. At the neutral point, the aircraft has zero static longitudinal stability margin.
What can cause aeroelastic divergence?
A Fuel pressure falls
B Landing gear extends
C Aerodynamic moment overcomes stiffness
D Cabin temperature rises
Answer: C. Aerodynamic moment overcomes stiffness. Divergence occurs when aerodynamic loading overcomes structural restoring stiffness.
Flutter is a dynamic interaction between aerodynamics and what?
A Fuel chemistry
B Cabin pressure
C Landing friction
D Structural motion
Answer: D. Structural motion. Flutter is a self-excited interaction of aerodynamic, elastic, and inertial forces.
Why must designers assess control-surface flutter?
A It lowers fuel density
B It can grow rapidly
C It improves stability
D It reduces wing loading
Answer: B. It can grow rapidly. Flutter can become destructive if not controlled.
What is control reversal?
A A pilot reverses throttle
B A wing changes sweep
C Control input reverses effect
D A gear retracts
Answer: C. Control input reverses effect. Aeroelastic twist can reverse the intended effect of a control input.
At higher Mach number, what can rise sharply?
A Wave drag
B Wing area
C Payload volume
D Landing gear track
Answer: A. Wave drag. Near transonic conditions, compressibility can cause a rapid drag rise.
Ground effect most directly changes induced drag near what?
A The tropopause
B The wing root
C The engine inlet
D The ground
Answer: D. The ground. Near the surface, reduced downwash can reduce induced drag.
What does the design envelope include besides speed?
A Seat fabric
B Weight and CG limits
C Paint code
D Cockpit sound
Answer: B. Weight and CG limits. Structural design accounts for critical weight, CG, altitude, and operating parameters.
Why do gust loads matter in airframe design?
A They add transient loads
B They reduce mass
C They set cabin color
D They eliminate fatigue
Answer: A. They add transient loads. Atmospheric gusts create additional structural loads that must be considered.
What does static longitudinal stability require after a pitch disturbance?
A Increasing yaw
B Zero lift
C Restoring pitching tendency
D Immediate stall
Answer: C. Restoring pitching tendency. Positive static stability produces an initial tendency to return toward trim.
Aft CG movement generally reduces what?
A Wing loading
B Engine thrust
C Tail arm
D Longitudinal static margin
Answer: D. Longitudinal static margin. Moving CG aft toward the neutral point reduces positive static margin.
Which wing feature can limit tip stall progression?
A High sweep only
B Washout
C Anhedral only
D A shorter fuselage
Answer: B. Washout. Washout lowers tip incidence, helping the root stall first.
What does structural envelope coverage require?
A Only cruise condition
B Only empty weight
C Critical parameter combinations
D One altitude only
Answer: C. Critical parameter combinations. Structural substantiation considers critical combinations within the design envelope.
Why design for limit and ultimate loads?
A Provide strength margin
B Increase drag
C Reduce stability
D Set passenger count
Answer: A. Provide strength margin. Limit loads define service design conditions; ultimate loads include a safety margin.
Which aeroelastic effect changes wing shape under load?
A Fuel slosh only
B Ground friction
C Cabin pressurization
D Elastic deformation
Answer: D. Elastic deformation. Aeroelasticity concerns interactions between aerodynamic forces and elastic deformation.
A gust alleviation system aims to reduce what?
A Wing area
B Fuel flow
C Peak structural loads
D Landing speed
Answer: C. Peak structural loads. Gust alleviation reduces the peak loads transferred to the structure.