Difficulty: Easy & Basic
What do winglets mainly reduce?
A Induced drag
B Landing weight
C Cabin pressure
D Fuel density
Answer: A. Induced drag. Winglets weaken wingtip vortices and can reduce induced drag.
Washout gives the wing tip what?
A Higher sweep
B Lower incidence
C More dihedral
D Greater camber
Answer: B. Lower incidence. Washout reduces tip angle of incidence relative to the root.
Taper ratio compares tip chord with what?
A Wing span
B Fuselage length
C Root chord
D Tail chord
Answer: C. Root chord. Taper ratio is tip chord divided by root chord.
Wing dihedral primarily improves which stability?
A Longitudinal
B Directional
C Spiral only
D Lateral
Answer: D. Lateral. Dihedral contributes to lateral stability in sideslip.
Why use washout near the wing tip?
A Improve stall progression
B Increase tail volume
C Reduce cabin noise
D Raise engine thrust
Answer: A. Improve stall progression. Washout helps the wing root stall before the tip, preserving aileron effectiveness longer.
A dorsal fin primarily helps which motion?
A Pitch trim
B Roll authority
C Wing lift
D Yaw stability
Answer: D. Yaw stability. A dorsal fin can increase directional stability.
What does a tail-volume coefficient compare?
A Wing fuel mass
B Tail size and leverage
C Engine thrust and drag
D Gear track and span
Answer: B. Tail size and leverage. Tail volume relates tail area and moment arm to a reference wing dimension.
Why may designers add wing twist?
A Increase cabin volume
B Reduce engine noise
C Set spanwise incidence
D Move landing gear
Answer: C. Set spanwise incidence. Twist sets local angle of incidence along the wing span.
What does a fairing usually reduce?
A Interference drag
B Structural weight only
C Lift coefficient
D Fuel temperature
Answer: A. Interference drag. Fairings smooth junctions and reduce interference drag.
A canard places a lifting surface where?
A Below the tail
B Inside the fuselage
C Ahead of main wing
D Behind the rudder
Answer: C. Ahead of main wing. A canard is a foreplane ahead of the main wing.
What is a flying-wing configuration notable for?
A No wing
B No control surfaces
C No propulsion option
D No separate tailplane
Answer: D. No separate tailplane. A flying wing integrates lifting surfaces without a conventional fuselage-tail arrangement.
Why can a T-tail risk deep stall?
A Gear blocks elevator
B Wing wake blankets tail
C Rudder increases lift
D Winglets stop pitch
Answer: B. Wing wake blankets tail. At high angle of attack, separated wing flow can blanket the high-mounted tail.
Where is a typical winglet attached?
A Wing tip
B Fuselage nose
C Tail root
D Landing gear
Answer: A. Wing tip. Winglets are vertical or canted surfaces mounted at the wingtip.
What does a pylon support?
A Tail trim tab
B Cabin floor
C Landing light
D Engine attachment
Answer: D. Engine attachment. A pylon attaches an external engine to the airframe.
What can an engine nacelle influence besides thrust?
A Fuel color
B Seat count
C Drag and flow
D Wing loading only
Answer: C. Drag and flow. Nacelle shape affects drag and local airflow around the aircraft.
A tail arm is measured from CG to what?
A Wing tip
B Tail aerodynamic center
C Nose gear
D Engine inlet
Answer: B. Tail aerodynamic center. Tail moment arm is measured from the center of gravity to the tail’s aerodynamic center.
Why use a dorsal fin on some aircraft?
A Improve directional stability
B Increase wing area
C Reduce payload
D Lower aspect ratio
Answer: A. Improve directional stability. A dorsal fin adds side area aft and can improve yaw stability.
What is anhedral?
A Upward wing angle
B Wing sweep forward
C Downward wing angle
D Wing twist aft
Answer: C. Downward wing angle. Anhedral is a downward angle between a wing and the lateral horizontal plane.
A larger tail moment arm can provide what?
A Less tail leverage
B More stabilizing moment
C No pitch control
D Higher wing loading
Answer: B. More stabilizing moment. A longer moment arm increases the tail’s moment for a given force.
Why position fuel tanks near the wing?
A Increase fuselage drag
B Move CG aft always
C Reduce lift
D Reduce bending loads
Answer: D. Reduce bending loads. Wing fuel can relieve wing bending by placing mass along the span.
Wing incidence is measured relative to which reference?
A Fuselage reference line
B Ground track
C Rudder hinge
D Engine shaft
Answer: A. Fuselage reference line. Wing incidence is the fixed angle between wing chord and fuselage reference line.
High wing placement can aid which design feature?
A Supersonic inlet
B Tail volume
C Ground clearance
D Fuel atomization
Answer: C. Ground clearance. A high wing can provide greater ground clearance for the fuselage or propeller.
What does the landing-gear track describe?
A Wheelbase length
B Wing span
C Tail arm
D Wheel spacing across aircraft
Answer: D. Wheel spacing across aircraft. Track is the lateral distance between the main landing gear wheels.
Why streamline a junction between wing and fuselage?
A Increase stall speed
B Reduce local flow separation
C Reduce lift
D Raise tail drag
Answer: B. Reduce local flow separation. A smooth fillet can reduce local separation and interference drag.
Which wing parameter is span divided by mean chord?
A Taper ratio
B Sweep angle
C Aspect ratio
D Dihedral angle
Answer: C. Aspect ratio. Aspect ratio is wing span squared divided by wing area, equivalent to span over mean chord.