Track is 1.6 m and CG height is 0.8 m. What is the simple rigid-body rollover threshold?
A 0.5 g
B 1.5 g
C 1.0 g
D 2.0 g
Answer: C. 1.0 g. The ideal threshold is approximately track/(2 × CG height) = 1.6/(2 × 0.8) = 1 g.
If CG height doubles while track stays fixed, ideal rollover threshold does what?
A Doubles
B Stays unchanged
C Falls by one quarter
D Falls by half
Answer: D. Falls by half. The simple threshold varies inversely with CG height when track width is fixed.
What does a single-track bicycle model replace each axle with?
A Two separate wheels
B One equivalent tire
C A rigid body only
D One suspension spring
Answer: B. One equivalent tire. The bicycle model combines the left and right tires at each axle into an equivalent front and rear tire.
Why does a linear bicycle model lose accuracy near the handling limit?
A Tire forces become nonlinear
B Wheelbase changes rapidly
C Mass becomes zero
D Yaw axis moves
Answer: A. Tire forces become nonlinear. Near saturation, tire force no longer rises linearly with slip angle.
What does a positive understeer gradient require as lateral acceleration rises?
A More steering angle
B Less steering angle
C No steering input
D Reverse steering
Answer: A. More steering angle. Positive understeer means the driver must add steering angle to hold the same turning radius as cornering demand rises.
An understeer gradient of zero describes which response?
A Oversteer
B Understeer
C Wheel hop
D Neutral steer
Answer: D. Neutral steer. Zero understeer gradient corresponds to neutral-steer behavior in the linear steady-state model.
A negative understeer gradient indicates which tendency?
A Understeer
B Neutral steer
C Pure roll
D Oversteer
Answer: D. Oversteer. A negative gradient means the rear axle develops greater slip tendency relative to the front.
As an oversteer vehicle approaches critical speed, what response can rise sharply?
A Rolling resistance
B Yaw-rate gain
C Wheelbase
D Spring rate
Answer: B. Yaw-rate gain. In an ideal linear oversteer model, yaw response becomes increasingly sensitive as speed approaches critical speed.
A 1.5 kN·m yaw moment acts on 2,500 kg·m² inertia. What yaw acceleration results?
A 0.6 rad/s²
B 0.15 rad/s²
C 1.67 rad/s²
D 3.75 rad/s²
Answer: A. 0.6 rad/s². Yaw acceleration is moment divided by yaw inertia: 1,500/2,500 = 0.6 rad/s².
What does greater yaw moment of inertia do for the same applied moment?
A Reduces yaw acceleration
B Increases yaw acceleration
C Removes tire slip
D Raises lateral grip
Answer: A. Reduces yaw acceleration. Angular acceleration equals moment divided by inertia, so greater yaw inertia gives a smaller response.
Vehicle sideslip angle compares heading with what?
A Direction of travel
B Wheelbase direction
C Road-bank angle
D Steering-wheel angle
Answer: A. Direction of travel. Sideslip angle is the difference between the vehicle’s longitudinal heading and its velocity direction.
Tire relaxation length describes what?
A Spring length at rest
B Distance for force buildup
C Wheelbase under load
D Brake-line expansion
Answer: B. Distance for force buildup. Relaxation length characterizes how tire force builds toward steady state after a change in slip.
Under a simple relaxation-length model, doubling speed does what to force-response time?
A Doubles
B Stays unchanged
C Becomes four times longer
D Halves
Answer: D. Halves. For fixed relaxation length, the time constant equals length divided by speed, so doubling speed halves it.
Pneumatic trail mainly creates what tire effect?
A Rolling resistance only
B Wheel lift
C Self-aligning torque
D Longitudinal load transfer
Answer: C. Self-aligning torque. Lateral force acts behind the contact-patch center, creating a restoring aligning moment.
A friction ellipse represents what?
A Rollover geometry
B Vehicle yaw inertia
C Combined tire-force limit
D Engine power curve
Answer: C. Combined tire-force limit. The friction ellipse shows that longitudinal and lateral tire forces share a finite adhesion capacity.
Hard braking in a turn leaves less capacity for what?
A Wheelbase
B Lateral tire force
C Yaw inertia
D Aerodynamic drag
Answer: B. Lateral tire force. Longitudinal braking force uses part of the tire’s available friction, reducing remaining cornering force.
Roll gradient is commonly expressed as what?
A N·m per rad
B km/h per turn
C rad/s per mass
D Degrees per g
Answer: D. Degrees per g. Roll gradient measures body roll angle per unit lateral acceleration, commonly reported in degrees per g.
How can lateral load transfer reduce total axle cornering capability?
A Total vehicle mass rises
B Grip gain is sublinear
C Track width disappears
D Inside tires gain pressure
Answer: B. Loaded tires gain proportionally less grip. Because tires are load-sensitive, the outside tire’s gain may be smaller than the inside tire’s loss.
At 25 m/s, yaw rate is 0.2 rad/s and sideslip is small. Lateral acceleration is about what?
A 0.2 m/s²
B 25 m/s²
C 5 m/s²
D 125 m/s²
Answer: C. 5 m/s². For small sideslip in a steady turn, lateral acceleration is approximately speed × yaw rate: 25 × 0.2 = 5 m/s².
Which change tends to increase understeer in a linear axle model?
A Lower rear cornering stiffness
B Higher rear grip only
C Shorter steering wheel
D Lower front cornering stiffness
Answer: D. Lower front cornering stiffness. Reduced front cornering stiffness requires more front slip angle and steering input for a given lateral force.
The simple rollover formula track/(2h) assumes what?
A Rigid quasi-static vehicle
B Flexible tire carcass only
C Highway-speed aerodynamics
D Active steering control
Answer: A. Rigid quasi-static vehicle. The formula is an idealized rigid-body threshold and omits suspension, tire, transient, and compliance effects.
Raising the roll center can increase which force path?
A Battery charging current
B Longitudinal drag
C Geometric lateral load transfer
D Brake-pedal leverage
Answer: C. Geometric lateral load transfer. Suspension links transmit a larger portion of lateral load through geometric force paths as roll-center geometry changes.
In a steady level turn, what remains approximately constant for all wheels combined?
A Inside-wheel load
B Total normal load
C Outside-wheel load
D Yaw rate always
Answer: B. Total normal load. A steady level turn redistributes normal load across the tires but leaves their combined load close to vehicle weight.
Which model resolves different left and right wheel loads?
A Bicycle model
B Single-track model
C Four-wheel model
D Point-mass model
Answer: C. Four-wheel model. A bicycle model combines left and right tires at each axle, while a four-wheel model resolves side-to-side loads.
Front lateral force is 3 kN at 1.2 m ahead of CG; rear force is 2 kN at 1.5 m behind. What net yaw moment results?
A 6.6 kN·m left yaw
B 0.6 kN·m right yaw
C 0 kN·m
D 0.6 kN·m left yaw
Answer: D. 0.6 kN·m left yaw. The front force creates 3.6 kN·m left yaw and the rear force 3.0 kN·m opposite yaw, leaving 0.6 kN·m left.