For a beam, bending moment is often extreme where…
A Deflection is zero
B Shear is zero
C Load is zero
D Axial stress peaks
Answer: B. Shear is zero. Since dM/dx = V, a moment extremum occurs where shear is zero or changes sign.
A simply supported beam has full-span UDL w. Maximum moment is…
A wL²/2
B wL/4
C wL²/8
D wL²/12
Answer: C. wL²/8. For a simply supported beam under uniform load, the maximum sagging moment is wL²/8 at midspan.
A cantilever carries full-span UDL w. Fixed-end moment magnitude?
A wL²/2
B wL²/8
C wL/4
D wL²/12
Answer: A. wL²/2. The fixed-end moment for a cantilever with full-span UDL is wL²/2.
A local notch raises peak stress while nominal stress stays low. This is…
A Creep relaxation
B Stress concentration
C Pure bending
D Uniform strain
Answer: B. Stress concentration. Geometric discontinuities create local stress amplification.
An open thin-walled section is generally less torsionally stiff than…
A A smaller area
B A longer beam
C A solid bar always
D A closed section
Answer: D. A closed section. Closed cells resist torsion efficiently through circulating shear flow.
A fixed-free column has effective length about…
A 2L
B L
C 0.7L
D 0.5L
Answer: A. 2L. For ideal fixed-free end conditions, effective length factor K is 2.
Euler buckling theory is most applicable to…
A Short crushing blocks
B Plastic hinges only
C Flexible cables
D Slender elastic columns
Answer: D. Slender elastic columns. Euler theory models elastic instability of sufficiently slender compression members.
A short stocky column usually reaches failure by…
A Material crushing
B Elastic buckling first
C Torsional flutter
D Fatigue only
Answer: A. Material crushing. Short columns tend to fail by compressive material strength rather than global buckling.
An impact load can create higher stress because…
A Material loses density
B Energy is applied rapidly
C Area becomes infinite
D Strain is always zero
Answer: B. Energy is applied rapidly. Dynamic loading can produce stresses above the equivalent static load response.
A brittle material typically has…
A Little plastic deformation
B Large ductility
C A broad yield plateau
D Unlimited elongation
Answer: A. Little plastic deformation. Brittle materials fracture with little plastic deformation compared with ductile materials.
A bonded composite beam is analyzed using…
A Compatible strain distribution
B Independent layer curvature
C Zero interface force
D Equal material moduli
Answer: A. Compatible strain distribution. Bonding enforces a common curvature and compatible longitudinal strain at the interface.
A transformed-section method replaces one material using…
A Poisson ratio only
B Safety factor
C Load factor only
D Modular ratio
Answer: D. Modular ratio. The modular ratio converts areas so a composite section can be analyzed with one reference modulus.
Castigliano’s theorem obtains displacement from…
A Area under load diagram
B Derivative of strain energy
C Stress times area
D Moment divided by length
Answer: B. Derivative of strain energy. For linear elastic systems, partial derivative of strain energy with respect to a load gives its displacement.
A beam load not through its shear center can produce…
A Axial compression only
B Uniform dilation
C Twist and bending
D No shear flow
Answer: C. Twist and bending. Eccentric transverse loading relative to the shear center creates torsion in addition to bending.
Principal stresses act on planes with…
A Zero in-plane shear
B Maximum shear
C Zero normal stress
D Maximum rotation
Answer: A. Zero in-plane shear. Principal planes carry normal stress with zero shear stress on that plane.
For plane stress, maximum in-plane shear is the radius of…
A The strain gauge
B The neutral axis
C The yield plateau
D Mohr’s circle
Answer: D. Mohr’s circle. The Mohr circle radius gives maximum in-plane shear stress.
Von Mises theory is often used for yielding of…
A Brittle glass only
B Unreinforced soil
C Ductile isotropic metals
D Perfect fluids
Answer: C. Ductile isotropic metals. The distortion-energy criterion predicts yielding of ductile isotropic materials.
Maximum principal stress theory is often used for…
A Fatigue crack growth only
B Ductile shear yielding
C Creep rate calculations
D Brittle failure estimates
Answer: D. Brittle failure estimates. A maximum normal stress criterion is commonly applied as a simple brittle failure model.
A fatigue notch is especially concerning because it…
A Removes mean stress
B Raises local cyclic stress
C Stops crack growth
D Reduces all strain
Answer: B. Raises local cyclic stress. Stress concentration can accelerate crack initiation under repeated loading.
A fully restrained bar heated uniformly develops…
A Zero axial stress
B Tensile thermal stress
C Compressive thermal stress
D Pure bending only
Answer: C. Compressive thermal stress. A bar prevented from expanding develops compressive stress when heated.
Initial crookedness in a column generally…
A Raises Euler capacity
B Eliminates bending
C Reduces practical buckling capacity
D Has no effect
Answer: C. Reduces practical buckling capacity. Imperfections create bending under axial load and reduce real column strength.
Unsymmetrical bending occurs when load acts…
A Through both principal axes
B Only along the beam
C At the neutral axis only
D Away from principal axes
Answer: D. Away from principal axes. Bending about nonprincipal axes can cause coupled curvature and stress distributions.
Mohr’s circle is used to transform…
A Beam span into load
B Area into volume
C Stress components by plane angle
D Modulus into strain
Answer: C. Stress components by plane angle. Mohr’s circle graphically represents normal and shear stresses on rotated planes.
A three-element strain rosette can estimate…
A In-plane principal strains
B Young’s modulus alone
C Crack depth directly
D Beam reaction forces
Answer: A. In-plane principal strains. Measurements in multiple directions allow reconstruction of in-plane strain components.
A beam’s neutral axis shifts in a composite section because…
A Shear force is zero
B Materials have different moduli
C Supports rotate freely
D Load becomes thermal
Answer: B. Materials have different moduli. The transformed stiffness distribution determines the neutral axis for a composite section.