Capacity design in seismic frames generally favors…
A Beam hinging before columns
B Column hinging first
C Joint shear failure
D Brittle bar pullout
Answer: A. Beam hinging before columns. The strong-column weak-beam hierarchy favors ductile beam hinges while protecting columns and joints.
Lap splices in seismic columns should avoid…
A Low-moment midheight only
B Straight bar lengths
C Potential hinge regions
D Protected joint zones
Answer: C. Potential hinge regions. Splices are kept away from regions expected to undergo large inelastic rotations.
Confinement ties in a column plastic hinge region should be…
A Closely spaced
B Omitted completely
C Widely spaced
D Only at midheight
Answer: A. Closely spaced. Closely spaced transverse reinforcement confines concrete and restrains bar buckling where rotation demand is high.
Joint shear demand is high because…
A Concrete has no weight
B Columns carry no load
C Beam forces enter the joint
D The slab is unloaded
Answer: C. Beam forces enter the joint. Joint cores transfer opposing beam and column actions and can experience large shear.
A slab-column connection under a large concentrated load needs checking for…
A Only flexural cracking
B Punching shear
C Only column buckling
D Only bar corrosion
Answer: B. Punching shear. The column reaction can create a two-way punching failure surface around the connection.
A deep beam’s load path is often represented by…
A Uniform flexure only
B Pure torsion loops
C A cable net only
D Compression struts and tension ties
Answer: D. Compression struts and tension ties. Strut-and-tie models represent disturbed regions through compression fields and tension ties.
Closed stirrups are important for beam torsion because they…
A Carry only axial compression
B Form a closed shear-flow path
C Prevent all cracking
D Replace longitudinal bars
Answer: B. Form a closed shear-flow path. Torsion requires a closed transverse reinforcement path plus longitudinal reinforcement.
Distribution reinforcement in slabs helps control…
A Crack width and shrinkage
B Column axial capacity
C Footing bearing
D Concrete density
Answer: A. Crack width and shrinkage. Secondary reinforcement distributes local effects and helps control cracking.
A beam bar continuing into a support needs…
A No embedment
B Only a paint coating
C An unrestrained end
D Adequate anchorage
Answer: D. Adequate anchorage. Bars must develop force through sufficient anchorage and bond at supports.
Development length increases when bar stress demand…
A Falls to zero
B Has no relation
C Becomes compressive only
D Increases
Answer: D. Increases. Longer embedment is generally required to develop larger bar force through bond.
Bar spacing must allow…
A Aggregate blockage
B Vibrator exclusion
C Concrete flow and compaction
D Cover removal
Answer: C. Concrete flow and compaction. Adequate spacing allows concrete and aggregate to pass and permits proper consolidation.
Required cover is influenced by…
A Only beam length
B Exposure and fire requirements
C Only bar count
D Only concrete color
Answer: B. Exposure and fire requirements. Cover requirements depend on durability exposure and fire protection provisions.
Chloride ingress can promote…
A Steel yielding strength
B Concrete hydration
C Aggregate interlock
D Reinforcement corrosion
Answer: D. Reinforcement corrosion. Chlorides can break down steel passivity and initiate reinforcement corrosion.
Carbonation threatens reinforcement by…
A Increasing bar diameter
B Stopping all moisture
C Reducing concrete alkalinity
D Raising steel yield stress
Answer: C. Reducing concrete alkalinity. Carbonation lowers pore-solution alkalinity and can depassivate embedded steel.
Fire resistance of an RC member depends partly on…
A Cover and member dimensions
B Only aggregate color
C Only beam support type
D Only bar grade
Answer: A. Cover and member dimensions. Concrete cover and member size influence heating rate and fire endurance.
For a slab supported on four sides, a large long-to-short ratio favors…
A Equal two-way action
B Pure torsion
C One-way action
D No bending
Answer: C. One-way action. A high aspect ratio tends to direct most load toward the shorter-span supports.
A flat slab connection must consider unbalanced…
A Moment transfer
B Aggregate size
C Floor finish color
D Curing water only
Answer: A. Moment transfer. Slab-column connections transfer shear and may also transfer unbalanced moment.
A column design under axial load and bending uses…
A Shear-span ratio only
B P-M interaction
C Concrete slump
D Bar spacing only
Answer: B. P-M interaction. Combined axial force and bending moment determine column capacity.
Second-order column moments are amplified by…
A Concrete cover
B Bar bond only
C Curing time
D Lateral deflection under axial load
Answer: D. Lateral deflection under axial load. P-delta effects add moment when axial force acts through lateral displacement.
A brittle shear failure is undesirable because it is…
A Sudden with little warning
B Highly ductile
C Always reversible
D A serviceability limit only
Answer: A. Sudden with little warning. Shear failure can be abrupt, so reinforcement and capacity hierarchy should avoid it.
Diagonal shear cracking is controlled with…
A Transverse reinforcement
B Only top longitudinal bars
C Surface coating
D Curing compound
Answer: A. Transverse reinforcement. Stirrups or other transverse reinforcement bridge diagonal cracks and carry shear.
Serviceability checks are distinct from collapse checks because they address…
A Only ultimate strength
B Use and comfort
C Only footing size
D Only construction cost
Answer: B. Use and comfort. Serviceability addresses deflection, cracking, vibration and normal function under use.
Durability detailing should reduce…
A Steel area
B Water and chloride ingress
C Concrete strength
D Aggregate interlock
Answer: B. Water and chloride ingress. Appropriate cover, crack control and materials limit ingress that can damage reinforcement.
A beam-column joint detail must provide…
A Unanchored bars
B Open transverse ties
C No concrete consolidation
D Force transfer and confinement
Answer: D. Force transfer and confinement. Joint reinforcement and bar anchorage support shear transfer and ductile response.
Before approving an RC design, verify…
A Only analysis output
B Only bar diameter
C Load path and detailing
D Only concrete grade
Answer: C. Load path and detailing. Safe behavior depends on a complete load path and buildable, code-compliant detailing.