A material experiences tensile stress 20 MPa and strain 1 × 10⁻⁴. What is its Young’s modulus?
A 2 × 10¹¹ Pa
B 2 × 10⁷ Pa
C 2 × 10⁹ Pa
D 2 × 10¹² Pa
Answer: A. 2 × 10¹¹ Pa. E = stress/strain = 20 × 10⁶/(1 × 10⁻⁴) = 2 × 10¹¹ Pa.
In the initial straight portion of a tensile stress-strain graph, what does the slope represent?
A Density
B Young’s modulus
C Breaking strain
D Surface tension
Answer: B. Young’s modulus. The slope is stress divided by strain, which is Young’s modulus.
A wire’s tensile force rises linearly from zero to 80 N as it extends by 4 mm. What elastic energy is stored?
A 0.04 J
B 0.08 J
C 0.16 J
D 0.32 J
Answer: C. 0.16 J. For a linear force-extension graph, energy = ½FΔL = ½ × 80 × 0.004 = 0.16 J.
For a wetting liquid in a capillary, how does capillary rise h depend on tube radius r?
A h is proportional to r
B h is proportional to r²
C h is independent of r
D h is proportional to 1/r
Answer: D. h is proportional to 1/r. The capillary relation is h = 2γcosθ/(ρgr), so h ∝ 1/r.
For a single liquid interface, what is the relation between surface energy per unit area and surface tension?
A They are numerically equal
B Surface energy per area is always twice surface tension
C Surface energy per area is surface tension squared
D They have unrelated units and values
Answer: A. They are numerically equal. For one interface, surface energy per unit area has units J/m², equivalent to N/m, and equals γ.
A soap film has two exposed faces, each with area A. What is its surface energy?
A γA
B 2γA
C γA²
D 2A/γ
Answer: B. 2γA. Each face contributes γA, giving total energy 2γA.
How is bulk modulus B related to a small pressure change ΔP and volume change ΔV?
A B = (ΔV/V)/ΔP
B B = ΔP × ΔV
C B = −ΔP/(ΔV/V)
D B = −VΔP/ΔV²
Answer: C. B = −ΔP/(ΔV/V). Bulk modulus is the pressure increase divided by the magnitude of volume strain; the minus sign accounts for compression.
How is Poisson’s ratio ν defined for a stretched wire?
A Longitudinal strain divided by stress
B Stress divided by lateral strain
C Volume strain divided by pressure
D Negative lateral strain divided by longitudinal strain
Answer: D. Negative lateral strain divided by longitudinal strain. ν = −(lateral strain)/(longitudinal strain), making ν positive for ordinary lateral contraction.
Which formula gives the extension ΔL of a uniform wire under force F?
A ΔL = FL/(AY)
B ΔL = AY/(FL)
C ΔL = FAY/L
D ΔL = FY/(AL)
Answer: A. ΔL = FL/(AY). From stress = Y × strain, the wire extension is ΔL = FL/(AY).
Two wires have the same length, material, and load. Wire 1 has twice the cross-sectional area of wire 2. How do their extensions compare?
A Wire 1 extends twice as much
B Wire 1 extends half as much
C Wire 1 extends four times as much
D Their extensions are equal
Answer: B. Wire 1 extends half as much. For the same F, L, and Y, extension varies inversely with area.
What happens when a material is loaded beyond its elastic limit?
A It must return exactly to its original shape
B Its density becomes zero
C It may retain permanent deformation after unloading
D Its Young’s modulus becomes infinite
Answer: C. It may retain permanent deformation after unloading. Beyond the elastic limit, deformation is not fully reversible and plastic strain can remain.
For a spring, what does the slope of a force-versus-extension graph represent?
A Bulk modulus
B Poisson’s ratio
C Density
D Spring constant k
Answer: D. Spring constant k. In F = kx, the slope of F against x is k.
If the radius of a wetting capillary tube is reduced to half, what happens to the capillary rise?
A It doubles
B It halves
C It becomes four times as large
D It stays unchanged
Answer: A. It doubles. Because h ∝ 1/r, halving r doubles h.
In the ideal capillary-rise formula, what is the rise when the contact angle is 90°?
A The tube radius
B Zero
C Twice the tube radius
D Infinite
Answer: B. Zero. The vertical surface-tension component is proportional to cosθ, which is zero at 90°.
For one liquid surface, its area increases by ΔA. How much work is needed if surface tension is γ?
A 2γΔA
B γ/ΔA
C γΔA
D ΔA/γ
Answer: C. γΔA. Surface energy change for one interface is ΔE = γΔA.
What generally happens to a liquid’s surface tension as temperature increases?
A It increases linearly without limit
B It remains exactly fixed
C It changes into viscosity
D It decreases
Answer: D. It decreases. Increasing temperature generally reduces surface tension, which approaches zero near the critical point.
For a Newtonian fluid, how is shear stress related to dynamic viscosity η and velocity gradient?
A τ = η(dv/dy)
B τ = η/(dv/dy)
C τ = η + dv/dy
D τ = (dv/dy)/η²
Answer: A. τ = η(dv/dy). Newton’s viscosity law is τ = η(dv/dy).
Which is an equivalent SI unit for dynamic viscosity?
A kg·m·s⁻²
B kg·m⁻¹·s⁻¹
C kg·m⁻³
D N·m⁻¹
Answer: B. kg·m⁻¹·s⁻¹. Pa·s = (N/m²)s = kg·m⁻¹·s⁻¹.
For a small sphere moving slowly through a viscous fluid, what is Stokes’ drag magnitude?
A πηr²v
B 6πηr/v
C 6πηrv
D ηv/(6πr)
Answer: C. 6πηrv. For low-Reynolds-number motion of a sphere, Stokes’ law gives F = 6πηrv.
What begins at the yield point of a typical ductile material?
A A change from solid to liquid
B The first appearance of any elastic strain
C A loss of all molecular attraction
D Significant plastic deformation
Answer: D. Significant plastic deformation. Past the yield point, substantial permanent deformation develops.
What does the area under a force-extension graph represent?
A Work done and stored elastic energy
B Young’s modulus
C Density
D Poisson’s ratio
Answer: A. Work done and stored elastic energy. The area ∫F dx is the work done; in a reversible elastic range it is stored elastic energy.
What is elastic strain energy per unit volume for a linearly elastic material?
A Stress divided by strain
B ½ × stress × strain
C Stress plus strain
D Twice stress multiplied by strain squared
Answer: B. ½ × stress × strain. For linear loading, energy density is the triangular area under the stress-strain graph: ½σε.
For the same wire material, load, and cross-sectional area, how does extension change if the wire length triples?
A It becomes one third as large
B It becomes nine times as large
C It triples
D It stays the same
Answer: C. It triples. Wire extension is proportional to length: ΔL = FL/(AY).
A wetting liquid has contact angle increased from 0° to 60° in the same capillary. How does the rise change?
A It doubles
B It becomes zero
C It stays unchanged
D It becomes half as large
Answer: D. It becomes half as large. The height is proportional to cosθ; cos60° = 1/2 while cos0° = 1.
What are equivalent SI units of surface tension?
A N/m and J/m²
B N·m and J/m
C Pa·s and kg/m³
D kg·m/s and N/m²
Answer: A. N/m and J/m². Surface tension is force per length, N/m, equivalent dimensionally to energy per area, J/m².