What is the main purpose of power-system protection?
A Increase line voltage
B Store reserve energy
C Set system frequency
D Limit fault damage
Answer: D. Limit fault damage. Protection detects abnormal conditions and isolates affected equipment to limit damage and maintain service elsewhere.
What does a protective relay do when it detects a fault?
A Raises bus voltage
B Closes every feeder
C Changes system frequency
D Sends a trip signal
Answer: D. Sends a trip signal. The relay evaluates measured signals and commands a breaker to trip when its operating criteria are met.
Which device interrupts fault current in a power circuit?
A Current transformer
B Circuit breaker
C Voltage transformer
D Protective relay
Answer: B. Circuit breaker. A circuit breaker interrupts current; the relay decides when a trip is needed.
What does a current transformer provide to a relay?
A Scaled current signal
B Scaled voltage signal
C Mechanical trip force
D Frequency reference
Answer: A. Scaled current signal. A CT reproduces primary current at a safer secondary level for metering and protection.
What does a voltage transformer provide to protection equipment?
A Scaled current signal
B Arc-quenching gas
C Scaled voltage signal
D Trip-coil power
Answer: C. Scaled voltage signal. A VT reduces system voltage to a proportional value suitable for relays and meters.
What is primary protection intended to protect?
A Its assigned equipment zone
B The entire grid equally
C Only the control room
D All remote feeders
Answer: A. Its assigned equipment zone. Primary protection detects faults within its defined zone and clears them promptly.
When should backup protection operate?
A Before every main relay
B Only during normal load
C If primary protection fails
D After manual inspection
Answer: C. If primary protection fails. Backup protection clears a fault if the main protection or breaker fails.
What is relay pickup current?
A Maximum breaking current
B Normal charging current
C Rated bus voltage
D Minimum operating current
Answer: D. Minimum operating current. Pickup is the threshold above which a current-operated relay begins operating.
An overcurrent relay responds mainly to what?
A Power direction only
B Frequency phase angle
C Insulation temperature
D Current magnitude
Answer: D. Current magnitude. An overcurrent element operates when measured current exceeds its configured threshold.
What extra quantity does a directional relay assess?
A Oil temperature
B Current direction
C Breaker travel distance
D Conductor sag
Answer: B. Current direction. Directional protection determines whether current flows in the protected direction.
A differential relay compares which quantities?
A Voltages at two buses
B Currents at zone ends
C Breaker opening times
D Line temperatures
Answer: B. Currents at zone ends. Healthy-zone currents entering and leaving should balance after compensation.
A distance relay estimates which electrical quantity?
A Conductor temperature
B Generator speed
C Apparent impedance
D Transformer oil level
Answer: C. Apparent impedance. Distance relays use measured voltage and current to estimate impedance to a line fault.
What defines a protection zone?
A Its instrument-transformer boundaries
B Its tower paint color
C Its load forecast period
D Its tariff category
Answer: A. Its instrument-transformer boundaries. Protection zones are commonly bounded by CT locations to assign faults to equipment sections.
What does selectivity mean in protection?
A Isolate only the faulted section
B Trip every breaker at once
C Keep every fault energized
D Disconnect all generators
Answer: A. Isolate only the faulted section. Selective protection clears the smallest practical system section containing the fault.
What does protection sensitivity describe?
A Ability to carry load current
B Ability to detect weak faults
C Speed of manual switching
D Resistance to corrosion
Answer: B. Ability to detect weak faults. Sensitive protection can detect low-level faults while remaining secure for normal conditions.
What does protection reliability require?
A Correct action when required
B Permanent tripping under load
C Operation without DC supply
D Identical settings everywhere
Answer: A. Correct action when required. Reliable protection operates for in-zone faults and avoids unwanted operation outside its zone.
What does protection stability mean during an external fault?
A Trip the healthy zone
B Remain restrained
C Open every nearby line
D Reset all relay settings
Answer: B. Remain restrained. A stable scheme avoids tripping for faults outside its protected zone.
A fuse primarily protects a circuit from what?
A Excess current
B Low power factor
C High frequency
D Incorrect phase order
Answer: A. Excess current. A fuse melts when current and duration exceed its time-current characteristic.
What directly energizes a breaker trip mechanism?
A VT secondary winding
B CT primary conductor
C Trip coil
D Bus coupler bar
Answer: C. Trip coil. The breaker trip coil releases the opening mechanism after a protection command.
Why do substations use a DC battery for tripping?
A Trip power remains available
B It increases fault current
C It measures line impedance
D It cools breaker contacts
Answer: A. Trip power remains available. A station battery supplies trip circuits even if AC station service is disturbed.
Earth-fault protection detects current flowing where?
A Between frequency bands
B Toward earth
C Into a capacitor bank only
D Through a speed governor
Answer: B. Toward earth. Earth-fault elements detect residual or neutral current associated with phase-to-earth faults.
What condition can a thermal overload relay protect against?
A Lightning surge voltage
B Reverse power export
C Busbar differential current
D Sustained motor overload
Answer: D. Sustained motor overload. Thermal overload protection responds to heating from excessive motor current over time.
An underfrequency relay measures which system quantity?
A Line impedance
B Oil pressure
C Supply frequency
D Breaker contact gap
Answer: C. Supply frequency. An underfrequency element monitors frequency and may initiate corrective action.
What is secondary-injection testing used to check?
A Tower foundation strength
B Primary cable insulation only
C Breaker gas purity
D Relay response to injected signals
Answer: D. Relay response to injected signals. Secondary injection verifies relay logic and settings using test currents or voltages.
A breaker interrupting rating states its ability to do what?
A Carry any current indefinitely
B Measure current accurately
C Clear specified fault current
D Limit system frequency
Answer: C. Clear specified fault current. The interrupting rating states the fault current the breaker can clear under specified conditions.