Open-channel flow has a free surface exposed to what?
A Vacuum pressure
B Pipe wall
C Atmospheric pressure
D Critical pressure
Answer: C. Atmospheric pressure. Open-channel flow has a free surface typically exposed to atmosphere.
Froude number compares inertia with what effect?
A Gravity
B Viscosity only
C Surface tension only
D Elasticity
Answer: A. Gravity. The Froude number is the ratio of inertial to gravitational effects.
Subcritical open-channel flow has Froude number what?
A Less than one
B Equal to two
C Greater than one
D Infinite
Answer: A. Less than one. Subcritical flow has Fr < 1 and is relatively deep and slow.
Supercritical open-channel flow has Froude number what?
A Less than one
B Equal to zero
C Exactly one
D Greater than one
Answer: D. Greater than one. Supercritical flow has Fr > 1 and is relatively shallow and fast.
Critical flow occurs at which Froude number?
A One
B Zero
C One-half
D Two
Answer: A. One. Critical flow occurs when Fr = 1.
Specific energy in a channel is measured above what?
A Atmospheric datum
B Pipe centerline
C Hydraulic grade line
D Channel bottom
Answer: D. Channel bottom. Specific energy is measured relative to the channel bottom.
A hydraulic jump dissipates what?
A Mass
B Mechanical energy
C Water density
D Channel width
Answer: B. Mechanical energy. Turbulence in a hydraulic jump dissipates substantial mechanical energy.
A weir is commonly used to measure what?
A Pipe roughness
B Bearing life
C Open-channel discharge
D Shaft torque
Answer: C. Open-channel discharge. A weir relates upstream head to channel discharge.
Manning equation estimates flow in what?
A Only closed steam lines
B Open channels
C Bearing clearances
D Nozzles only
Answer: B. Open channels. Manning’s equation is widely used for uniform open-channel flow.
Chezy’s formula relates velocity to hydraulic radius and what?
A Pressure ratio
B Pipe diameter only
C Vapor pressure
D Slope
Answer: D. Slope. Chezy velocity depends on hydraulic radius, energy slope and a roughness coefficient.
Buckingham Pi theorem reduces variables to what?
A Dimensionless groups
B Base units only
C Pressure terms only
D A single equation always
Answer: A. Dimensionless groups. Dimensional analysis expresses a relationship through independent dimensionless groups.
Reynolds similarity is important when viscous effects dominate in what?
A Temperature scales
B Model and prototype
C Surface color
D Material density only
Answer: B. Model and prototype. Matching Reynolds number is required when viscous forces govern model behavior.
Froude similarity is important when gravity effects dominate in what?
A Model and prototype
B Heat exchangers
C Bearing races
D Compressors only
Answer: A. Model and prototype. Froude matching is used for gravity-dominated free-surface models.
The Euler number compares pressure forces with what?
A Gravity only
B Surface tension only
C Elastic forces
D Inertial forces
Answer: D. Inertial forces. Euler number is a pressure-force to inertial-force ratio.
Drag acts parallel to the direction of what?
A Surface normal
B Free-stream flow
C Gravity always
D Lift force
Answer: B. Free-stream flow. Drag is the force component parallel to incoming flow.
Lift acts perpendicular to what?
A Surface tangent always
B Gravity only
C Free-stream flow
D Pressure gradient only
Answer: C. Free-stream flow. Lift is the force component perpendicular to the free-stream direction.
Flow separation is promoted by an adverse pressure gradient and what?
A Lower viscosity only
B Boundary-layer thickening
C Higher density only
D Zero curvature
Answer: B. Boundary-layer thickening. An adverse pressure gradient slows near-wall fluid and can cause boundary-layer separation.
Terminal settling velocity occurs when drag balances what?
A Surface tension only
B Pressure head
C Net particle weight
D Pipe friction
Answer: C. Net particle weight. At terminal velocity, net downward weight is balanced by drag and buoyancy.
A momentum equation is useful for force on a pipe what?
A Bend
B Thermometer
C Piezometer
D Barometer
Answer: A. Bend. Momentum balance relates fluid velocity change to reaction forces on bends and fittings.
A jet striking a stationary flat plate changes what to create force?
A Vapor pressure
B Fluid momentum
C Specific gravity
D Surface tension
Answer: B. Fluid momentum. The plate force follows the rate of change of jet momentum.
For a submerged body, buoyancy acts through what?
A Center of pressure
B Metacenter only
C Center of gravity always
D Center of buoyancy
Answer: D. Center of buoyancy. Buoyant force acts through the centroid of displaced fluid volume.
A converging nozzle generally increases flow what?
A Static pressure always
B Density to zero
C Velocity
D Viscosity
Answer: C. Velocity. A converging passage accelerates subsonic incompressible flow as area decreases.
A hydraulic grade line below pipe center may indicate what?
A Zero velocity
B High vapor pressure
C No flow
D Subatmospheric pressure
Answer: D. Subatmospheric pressure. If HGL is below pipe centerline datum, gauge pressure may be negative.
A laminar boundary layer on a flat plate grows with what distance?
A Pipe roughness only
B Fluid pressure only
C Downstream distance
D Surface tension
Answer: C. Downstream distance. The boundary layer thickens as fluid travels downstream along the plate.
A discharge coefficient accounts for what?
A Real-flow effects
B Fluid color
C Pipe weight
D Atmospheric pressure
Answer: A. Real-flow effects. Discharge coefficients correct ideal meter predictions for contraction and losses.