Difficulty: Easy & Basic
How is angle of attack defined?
A Wing chord vs horizon
B Chord line vs relative wind
C Flight path vs fuselage
D Bank angle vs horizon
Answer: B. Chord line vs relative wind. Angle of attack is measured between the wing chord line and the relative wind.
Relative wind points which way?
A Opposite flight direction
B Same flight direction
C Toward aircraft nose
D Along vertical axis
Answer: A. Opposite flight direction. Relative wind flows opposite the aircraftβs path through the air.
Rotation about the lateral axis produces which motion?
A Roll
B Yaw
C Heave
D Pitch
Answer: D. Pitch. Pitch is rotation about the lateral, or side-to-side, axis.
Aircraft yaw occurs about which axis?
A Lateral axis
B Longitudinal axis
C Vertical axis
D Wing chord axis
Answer: C. Vertical axis. Yaw is rotation about the aircraftβs vertical axis.
Rolling motion occurs about the aircraftβs what?
A Longitudinal axis
B Lateral axis
C Vertical axis
D Wing chord line
Answer: A. Longitudinal axis. Roll is rotation about the nose-to-tail longitudinal axis.
Exceeding which angle triggers a wing stall?
A Design cruise angle
B Critical angle of attack
C Zero-lift angle
D Incidence angle
Answer: B. Critical angle of attack. A stall occurs when the wing exceeds its critical angle of attack.
Static stability describes an aircraftβs initial tendency after what?
A Trim change
B Fuel burn
C Disturbance
D Runway roll
Answer: C. Disturbance. Static stability is the initial tendency to return toward or move away from equilibrium after a disturbance.
Dynamic stability tracks response over what?
A Wing span
B Ground distance
C Fuel volume
D Time
Answer: D. Time. Dynamic stability describes how the motion develops over time after the initial response.
Indicated airspeed comes from which sensing system?
A Gyro compass
B Pitot-static system
C Magnetometer
D GPS receiver
Answer: B. Pitot-static system. The pitot-static system senses the pressures used by the airspeed indicator.
Trimming mainly reduces what pilot workload?
A Control force
B Thrust demand
C Fuel temperature
D Wing loading
Answer: A. Control force. Trim relieves the sustained control force needed to maintain a selected condition.
Where is total aircraft weight treated as concentrated?
A Center of pressure
B Neutral point
C Center of gravity
D Quarter chord
Answer: C. Center of gravity. The center of gravity is the balance point where total aircraft weight is treated as acting.
Load factor is lift divided by which quantity?
A Wing area
B Airspeed
C Thrust
D Aircraft weight
Answer: D. Aircraft weight. Load factor is the ratio of aerodynamic lift to aircraft weight.
With a tailwind, groundspeed exceeds TAS by what?
A Tailwind component
B Headwind component
C Crosswind component
D Bank angle
Answer: A. Tailwind component. A tailwind adds to true airspeed to produce groundspeed.
At the same IAS, lower air density makes TAS do what?
A Decrease
B Increase
C Stay constant
D Reach zero
Answer: B. Increase. At ordinary subsonic speeds, the same indicated airspeed corresponds to greater true airspeed in thinner air.
Takeoff headwind usually does what to ground roll?
A Lengthens it
B Leaves it unchanged
C Eliminates lift
D Shortens it
Answer: D. Shortens it. A headwind provides more airflow over the wing at a given groundspeed and generally shortens takeoff roll.
Roll is primarily controlled by which surface?
A Rudder
B Elevator
C Ailerons
D Trim tab
Answer: C. Ailerons. Ailerons primarily control roll by changing lift on opposite wings.
Yaw is primarily controlled by which surface?
A Rudder
B Ailerons
C Elevator
D Flaps
Answer: A. Rudder. The rudder primarily controls yaw about the vertical axis.
Pitch is primarily controlled by which surface?
A Rudder
B Elevator
C Spoilers
D Ailerons
Answer: B. Elevator. The elevator primarily controls pitch about the lateral axis.
Moving CG toward the aft limit usually does what to longitudinal stability?
A Improves it
B Leaves it fixed
C Eliminates drag
D Reduces it
Answer: D. Reduces it. An aft center of gravity generally reduces longitudinal static stability.
In a coordinated turn, where should the inclinometer ball sit?
A Toward high wing
B Toward low wing
C Centered
D At the top
Answer: C. Centered. A centered ball indicates the turn is coordinated, with no measured slip or skid.
VSO denotes stall speed in which configuration?
A Landing configuration
B Cruise configuration
C Clean configuration
D Gear-up configuration
Answer: A. Landing configuration. VSO is the stall speed in the specified landing configuration.
What does a flight envelope plot against speed?
A Fuel pressure
B Load factor
C Cabin altitude
D Climb time
Answer: B. Load factor. A V-n diagram shows structural load factor across airspeed.
Why does high density altitude reduce climb performance?
A Higher gravity
B Increased wing area
C Lower gross weight
D Lower air density
Answer: D. Lower air density. Lower air density reduces engine, propeller, and aerodynamic performance for many aircraft.
Specific range expresses distance per what?
A Unit time
B Bank angle
C Fuel quantity
D Climb height
Answer: C. Fuel quantity. Specific range is distance traveled per unit of fuel consumed.
Endurance measures how long an aircraft can do what?
A Remain airborne
B Travel one mile
C Maintain heading
D Climb 1,000 feet
Answer: A. Remain airborne. Endurance is the time an aircraft can remain airborne under stated conditions.