Difficulty: Easy & Basic
Normal faults are most commonly associated with:
A Horizontal-only motion
B No displacement
C Tensional stress and extension
D Compression and crustal shortening
Answer: C. Tensional stress and extension. Normal faulting accommodates extension as the hanging wall moves down relative to the footwall.
Reverse and thrust faults are most commonly associated with:
A Seafloor spreading
B Wind erosion
C Tension only
D Compression
Answer: D. Compression. Reverse or thrust faulting accommodates crustal shortening under compression.
A strike-slip fault is dominated by movement:
A Vertically down a slope only
B By magma rising through it
C Horizontally past the opposite block
D Vertical motion only
Answer: C. Horizontally past the opposite block. Strike-slip faults accommodate chiefly horizontal motion parallel to the fault trace.
On a seismogram, the first prominent arrival from a distant earthquake is usually the:
A Love wave
B S wave
C Rayleigh wave
D P wave
Answer: D. P wave. P waves travel fastest through Earth and typically arrive first.
Which seismic body wave cannot travel through a liquid?
A P and S equally
B Neither wave
C S wave
D P wave
Answer: C. S wave. S waves require shear strength and therefore do not propagate through liquids.
The absence of direct S waves beyond certain angular distances from a large earthquake helped reveal:
A The Moon’s crust
B A permanent ocean trench
C A solid atmosphere
D Earth’s liquid outer core
Answer: D. Earth’s liquid outer core. S waves do not pass through the liquid outer core, producing an S-wave shadow zone.
P waves can travel through:
A Solids and liquids
B Neither solids nor liquids
C Solids only
D Liquids only
Answer: A. Solids and liquids. P waves are compressional waves and can travel through both solids and fluids.
A seismogram is:
A A measure of wind speed
B A record of ground motion
C A map of soil types
D A diagram of ocean salinity
Answer: B. A record of ground motion. A seismogram is the recorded trace of motion measured by a seismograph.
A larger gap between P- and S-wave arrivals at a station generally means the earthquake is:
A Closer to that station
B Smaller in magnitude by definition
C At the station itself
D Farther from that station
Answer: D. Farther from that station. Because P waves outrun S waves, their arrival-time separation increases with distance.
Why can shaking intensity differ between two places at similar distances from an earthquake?
A Different local site conditions
B Earthquakes have no surface waves
C P waves stop at borders
D Magnitude changes at every town
Answer: A. Different local site conditions. Ground conditions, focal depth, rupture direction, and structures influence local shaking and damage.
Soft, water-rich sediment can amplify earthquake shaking compared with:
A A cloud layer
B A vacuum
C The deep mantle
D Competent bedrock
Answer: D. Competent bedrock. Soft sediments can amplify ground motion relative to firm bedrock at some frequencies.
The Modified Mercalli Intensity scale has commonly used values from:
A I to XII
B A to Z
C 1 to 100
D 0 to 5
Answer: A. I to XII. The Modified Mercalli scale expresses observed intensity in Roman-numeral levels I through XII.
A magnitude scale differs from an intensity scale because magnitude:
A Value changes by location
B Source size; intensity varies
C Measures only local building damage
D Depends only on soil colour
Answer: B. Source size; intensity varies. Magnitude is a source measure; intensity describes shaking effects at particular places.
A tsunami warning is especially important after a strong nearby coastal earthquake because:
A Tsunami may arrive before warning
B All earthquakes produce tsunamis
C P waves act like wind
D The shoreline always rises permanently
Answer: A. Tsunami may arrive before warning. Large offshore earthquakes can displace the seafloor and send tsunami waves toward nearby coasts.
Liquefaction can cause buildings to settle or tilt because saturated loose soil:
A Becomes permanently dry
B Turns into solid granite
C Stops transmitting any motion
D Loses strength during strong shaking
Answer: D. Loses strength during strong shaking. Shaking can raise pore-water pressure and reduce the strength of loose saturated sediment.
Earthquake-triggered landslides are most likely on:
A Stable distant ocean basins
B Flat bedrock plains only
C Steep, unstable slopes shaken strongly
D Newly formed coral reefs
Answer: C. Steep, unstable slopes shaken strongly. Strong shaking can destabilize steep slopes and trigger landslides.
The mainshock-aftershock sequence reflects:
A Post-rupture stress adjustment
B Ocean currents pulling the fault
C Nearby planet movement
D Guaranteed larger quake
Answer: A. Post-rupture stress adjustment. Aftershocks occur as surrounding parts of the crust adjust after the main rupture.
Which statement about foreshocks is scientifically sound?
A Only at ocean ridges
B Known after larger quake
C Predict exact time and size
D Precede every earthquake
Answer: B. Known after larger quake. An earthquake is identified as a foreshock only after a larger mainshock occurs.
A seismic gap is best treated as:
A Quiet segment on active fault
B Guaranteed quake tomorrow
C Rain-caused seismogram gap
D Quake-free location
Answer: A. Quiet segment on active fault. Seismic gaps are considered in hazard research but do not provide a precise earthquake forecast.
Elastic strain builds on a locked fault when:
A Plates move; fault stays locked
B All tectonic stress disappears
C Fault replaced by magma
D The crust stops deforming entirely
Answer: A. Plates move; fault stays locked. A locked fault can accumulate elastic strain as tectonic forces continue to act.
An earthquake’s focal depth is the distance from the surface to its:
A Nearest seismic station
B Focus or hypocenter
C Epicenter
D Fault’s surface trace
Answer: B. Focus or hypocenter. Focal depth measures how far below Earth’s surface rupture begins.
Earthquake locations are commonly plotted with both epicenter and:
A Wind direction
B Cloud height
C Focal depth
D Tidal range
Answer: C. Focal depth. Epicentral position and depth together describe the earthquake’s location.
Surface waves can be especially damaging because they:
A Arrive before P waves
B Strong near-surface shaking
C Inner-core travel only
D Cannot shake buildings
Answer: B. Strong near-surface shaking. Surface waves can have large amplitudes and move the ground strongly near the surface.
The classic Richter scale was originally designed to measure:
A Tsunami height
B The depth of earthquake foci
C Local magnitude from wave amplitudes
D Damage on twelve-point scale
Answer: C. Local magnitude from wave amplitudes. Richter’s local-magnitude scale used the logarithm of seismographic wave amplitude.
The moment-magnitude scale is preferred for many large earthquakes because it relates to:
A The maximum Mercalli intensity
B Seismic moment and rupture size
C The number of aftershocks only
D Perceived loudness only
Answer: B. Seismic moment and rupture size. Moment magnitude is tied to seismic moment, including fault area, slip, and rock rigidity.