Difficulty: Hard
Fuel input is 140 kW; brake output 42 kW, exhaust 35 kW, radiation 3 kW. Coolant heat load?
A 42 kW
B 60 kW
C 70 kW
D 95 kW
Answer: B. 60 kW. The balance remainder is 140−42−35−3=60 kW to coolant.
Counterflow radiator has coolant 100→80°C and air 30→60°C; U=600 W/m²K, A=0.8 m². Duty?
A 18.0 kW
B 24.0 kW
C 21.5 kW
D 30.0 kW
Answer: C. 21.5 kW. Terminal differences are 40 and 50 K; LMTD≈44.8 K, so Q̇=600×0.8×44.8≈21.5 kW.
Radiator rejects 28 kW; Cmin=0.5 kW/K; inlet temperature gap=70 K. Effectiveness?
A 0.50
B 0.80
C 0.60
D 0.90
Answer: B. 0.80. Maximum possible transfer is 0.5×70=35 kW; effectiveness=28/35=0.80.
Water saturation temperature at 200 kPa absolute is closest to?
A 120°C
B 100°C
C 110°C
D 134°C
Answer: A. 120°C. Steam tables give a saturation temperature near 120°C at 200 kPa absolute.
The engine overheats in traffic but cools at highway speed. Which fault is likely?
A Fuel filter restriction
B Clutch slip
C Cooling fan not operating
D Low tire pressure
Answer: C. Cooling fan not operating. At low road speed, fan failure can remove needed airflow; highway motion supplies airflow.
Dirt blocks the radiator’s air passages. What effect is expected?
A Higher coolant pressure
B Lower air-side heat transfer
C More fuel atomization
D Longer valve overlap
Answer: B. Lower air-side heat transfer. Blocked fins reduce airflow and radiator heat rejection.
Several radiator core regions remain unusually cool while others are hot. What may this suggest?
A High fuel octane
B Excessive tire camber
C Low battery reserve
D Uneven or restricted coolant flow
Answer: D. Uneven or restricted coolant flow. Uneven core temperatures can indicate internal restriction or poor coolant distribution.
The thermostat remains closed after warm-up. What reading may appear first?
A Engine cool, radiator hot
B Engine hot, radiator cool
C Fuel rail hot, engine cold
D Oil pan cold, radiator hot
Answer: B. Engine hot, radiator cool. If coolant cannot reach the radiator, the engine may overheat while the radiator stays comparatively cool.
What condition can promote coolant-pump cavitation?
A High radiator airflow
B High battery voltage
C Low inlet pressure
D Low fuel temperature
Answer: C. Low inlet pressure. Low local pressure can form vapor bubbles that impair pump flow.
A damaged pump impeller may cause what under sustained load?
A Higher rail pressure
B Insufficient coolant circulation
C Lower exhaust noise
D Increased oil octane
Answer: B. Insufficient coolant circulation. Impeller damage can reduce coolant flow and cause overheating under load.
After refill, cabin heat and temperature gauge fluctuate. What is a likely cause?
A High fuel octane
B Worn clutch lining
C Trapped air in circuit
D Excess tire pressure
Answer: C. Trapped air in circuit. Air pockets can interrupt coolant flow and cause erratic heater output or temperature.
A replacement cap has a lower pressure rating than specified. What risk increases?
A Premature coolant boiling
B Higher compression ratio
C Reduced fuel volatility
D Greater fan speed
Answer: A. Premature coolant boiling. Lower system pressure reduces the boiling-point margin.
A cap vacuum valve stays closed during cool-down. What may happen?
A Hoses can collapse inward
B Fuel injectors open
C Radiator fins expand
D Oil pressure rises
Answer: A. Hoses can collapse inward. Failure to admit return flow can create vacuum and collapse a weak hose.
The cooling system pressurizes rapidly from a cold start. What should be investigated?
A Fan shroud alignment
B Fuel filter color
C Combustion gas leakage
D Tire tread depth
Answer: C. Combustion gas leakage. Rapid pressure buildup can indicate combustion gases entering coolant through a leak.
What is the usual temperature response of an NTC coolant sensor?
A Resistance decreases as temperature rises
B Resistance rises as temperature rises
C Resistance stays fixed
D Resistance becomes zero when cold
Answer: A. Resistance decreases as temperature rises. An NTC thermistor’s resistance falls as its temperature increases.
How does PWM control vary electric-fan speed?
A Changes cylinder bore
B Changes coolant chemistry
C Changes radiator pressure cap
D Changes duty cycle
Answer: D. Changes duty cycle. Pulse-width modulation varies average motor power through its duty cycle.
Burned relay contacts can produce which fan symptom?
A Fan fails to receive power
B Coolant freezes instantly
C Thermostat opens early
D Fuel rail pressure rises
Answer: A. Fan fails to receive power. Damaged relay contacts can interrupt current to an electric fan.
A fan motor draws unusually high current and makes noise. What may be wrong?
A Low coolant concentration
B Blocked fuel return
C Loose piston ring
D Binding motor or bearing
Answer: D. Binding motor or bearing. Mechanical binding or bearing wear can increase current and create noise.
A leaking oil cooler can cause what cross-contamination?
A Oil and coolant mixing
B Fuel and brake fluid mixing
C Air and diesel mixing
D Coolant and tire sealant mixing
Answer: A. Oil and coolant mixing. A failed oil-to-coolant heat exchanger can allow the two fluids to mix.
A coolant sensor reads colder than actual temperature. What control error may follow?
A Fuel tank overfills
B Radiator pressure rises
C Water pump reverses
D Fan activation may be delayed
Answer: D. Fan activation may be delayed. The ECU may delay fan operation if the temperature signal is biased low.
Why can a missing fan shroud reduce cooling at idle?
A Coolant pressure doubles
B Fuel return stops
C Thermostat closes mechanically
D Air bypasses parts of core
Answer: D. Air bypasses parts of core. Without a shroud, fan airflow can bypass portions of the radiator core.
Why must a bypass passage remain open when thermostat blocks radiator flow?
A Increase exhaust temperature
B Raise fuel rail pressure
C Maintain engine-side circulation
D Prevent oil lubrication
Answer: C. Maintain engine-side circulation. The bypass supports circulation through the engine during warm-up with radiator flow restricted.
Coolant is at 110°C and saturation temperature at system pressure is 120°C. Boiling margin?
A 5 K
B 20 K
C 30 K
D 10 K
Answer: D. 10 K. Boiling margin is saturation temperature minus coolant temperature: 120−110=10 K.
Why might an electric fan run briefly after engine shutdown?
A Raise fuel pressure
B Manage retained heat
C Charge the starter
D Open the thermostat mechanically
Answer: B. Manage retained heat. Some control strategies run the fan after shutdown to manage heat soak.
Before opening a hot pressurized radiator cap, what is safest?
A Open it quickly
B Rev the engine
C Let system cool fully
D Remove the fan belt
Answer: C. Let system cool fully. Cooling lets pressure fall and reduces scalding risk from hot coolant or steam.