Difficulty: Hard
Under uniform-wear theory for a clutch lining, what is approximately constant?
A Pressure times radius
B Pressure alone
C Friction times speed
D Torque times area
Answer: A. Pressure times radius. Uniform-wear analysis assumes pressure varies inversely with radius, so pressure times radius is constant.
What does uniform-pressure theory assume across the annular lining?
A Constant sliding speed
B Constant friction radius
C Constant gear ratio
D Constant contact pressure
Answer: D. Constant contact pressure. Uniform-pressure theory treats contact pressure as constant across the friction face.
For uniform wear, inner radius=0.06 m and outer radius=0.14 m. Mean radius?
A 0.08 m
B 0.12 m
C 0.10 m
D 0.20 m
Answer: C. 0.10 m. Uniform-wear mean radius=(0.14+0.06)/2=0.10 m.
Two rotating members have inertias 0.20 and 0.80 kgΒ·mΒ². Reduced inertia?
A 0.32 kgΒ·mΒ²
B 0.50 kgΒ·mΒ²
C 1.00 kgΒ·mΒ²
D 0.16 kgΒ·mΒ²
Answer: D. 0.16 kgΒ·mΒ². Equivalent inertia for relative motion=I1I2/(I1+I2)=0.20Γ0.80/1.00=0.16 kgΒ·mΒ².
Reduced inertia is 0.16 kgΒ·mΒ² and relative speed is 100 rad/s. Synchronization energy?
A 160 J
B 800 J
C 1,600 J
D 8,000 J
Answer: B. 800 J. Energy dissipated=Β½IeqΞΟΒ²=0.5Γ0.16Γ100Β²=800 J.
Why can clutch torque capacity fall after severe overheating?
A Gear ratio increases
B Flywheel radius doubles
C Hydraulic fluid freezes
D Friction coefficient may fade
Answer: D. Friction coefficient may fade. High temperature can reduce friction material performance and weaken torque capacity.
What can repeated severe slip do to a friction lining?
A Increase its tooth count
B Glaze or overheat it
C Improve its oil seal
D Raise its spring rate
Answer: B. Glaze or overheat it. Repeated slip creates heat that can glaze or damage the lining.
What does a concentric slave cylinder combine?
A Slave cylinder and release bearing
B Master cylinder and flywheel
C Clutch disc and gearbox
D Pilot bearing and pressure plate
Answer: A. Slave cylinder and release bearing. A concentric slave cylinder surrounds the input shaft and integrates release-bearing action.
Why repair a leaking hydraulic clutch promptly?
A It raises engine torque
B It changes gear ratio
C Fluid loss can prevent release
D It increases flywheel inertia
Answer: C. Fluid loss can prevent release. Loss of hydraulic fluid can reduce release travel and leave the clutch dragging.
What prevents two gearbox gears engaging at once?
A Shift interlock
B Release bearing
C Pilot bearing
D Oil strainer
Answer: A. Shift interlock. An interlock blocks simultaneous selection of incompatible gear paths.
What defines a constant-mesh gearbox?
A Gears leave mesh every shift
B No shafts are parallel
C Gear pairs remain meshed
D Only one gear is fitted
Answer: C. Gear pairs remain meshed. In a constant-mesh design, gear pairs stay meshed and selection uses a coupling device.
What does a dog clutch do inside a constant-mesh gearbox?
A Synchronizes engine coolant
B Locks gear to shaft
C Pumps oil between gears
D Changes tire torque
Answer: B. Locks gear to shaft. Dog teeth couple the selected free gear to its shaft.
Why double-clutch an unsynchronized gearbox?
A Increase engine compression
B Match shaft speeds manually
C Reduce coolant temperature
D Lock the differential
Answer: B. Match shaft speeds manually. The driver changes shaft speed through neutral to reduce mismatch before engaging the next gear.
How does a synchronizer cone help during shifting?
A Hydraulic pressure changes ratio
B Friction equalizes rotational speeds
C Coolant cools the gear teeth
D Oil seals close the shaft
Answer: B. Friction equalizes rotational speeds. Cone friction brings the gear and shaft closer to a matching speed before dog engagement.
Grinding in only one forward gear may suggest wear in which part?
A Radiator thermostat
B That gear’s synchronizer
C Clutch master cylinder
D Fuel-pressure regulator
Answer: B. That gear’s synchronizer. A gear-specific clash can indicate wear in that ratio’s synchronizer or engagement teeth.
What does a gearbox detent help do?
A Pump clutch fluid
B Cool the flywheel
C Adjust tire pressure
D Hold the selected gear
Answer: D. Hold the selected gear. A detent resists vibration-driven movement of the shift rail from its selected position.
Why should a shift fork not carry continuous driving torque?
A It can wear or bend
B It raises oil viscosity
C It lowers engine power
D It expands the clutch disc
Answer: A. It can wear or bend. The fork is intended to position a sleeve, not act as a torque-bearing member.
What does bearing preload control in a gearbox shaft?
A Fuel flow rate
B Clutch friction coefficient
C Endplay and bearing stiffness
D Radiator air speed
Answer: C. Endplay and bearing stiffness. Preload removes or controls bearing clearance to set stiffness and shaft position.
Excessive axial shaft endplay can disturb what?
A Coolant concentration
B Clutch pedal ratio
C Fuel vapor pressure
D Gear alignment and engagement
Answer: D. Gear alignment and engagement. Uncontrolled axial movement can shift gear position and alter contact or engagement.
What is a marking compound used for on gear teeth?
A Measure oil density
B Set clutch pedal height
C Test fuel pressure
D Check contact pattern
Answer: D. Check contact pattern. A marking compound shows where mating tooth surfaces contact under load.
Why can too little bearing clearance or excessive preload overheat a gearbox?
A Lower gear-mesh frequency
B More fuel vapor
C Higher friction and load
D Less shaft rotation
Answer: C. Higher friction and load. Excessive preload increases bearing friction and temperature.
What may excessive synchronizer wear cause during a shift?
A Gear clash
B Coolant leakage
C Clutch overfill
D Higher tire grip
Answer: A. Gear clash. A worn synchronizer may fail to equalize shaft and gear speeds before engagement.
Why avoid forcing a gear lever during a clash?
A Raise transmission pressure
B Increase clutch capacity
C Protect synchronizer and dog teeth
D Open the differential
Answer: C. Protect synchronizer and dog teeth. Forcing engagement can damage friction cones, dog teeth, or shift components.
Which lubrication method is common in many manual gearboxes?
A Fuel injection
B Splash lubrication
C Coolant atomization
D Dry-air lubrication
Answer: B. Splash lubrication. Many manual gearboxes use rotating gears to splash oil onto gears and bearings.
A gearbox is noisy only in one ratio. What should inspection prioritize?
A That gear pair and bearings
B Radiator fan bearings
C Fuel pump relay
D Clutch pedal spring
Answer: A. That gear pair and bearings. A ratio-specific noise points first to that gear pair and its supporting bearings.