The production reactor runs hotter as its volume increases even though inlet coolant is unchanged. Which scale-up issue deserves attention first?
A antibody affinity in a separate assay
B the plant variety used for feedstock only
C the label size on the cooling line
D heat-transfer area and cooling capacity relative to metabolic heat generation
Answer: D. heat-transfer area and cooling capacity relative to metabolic heat generation. Larger reactors must remove metabolic heat effectively as heat generation rises with culture volume.
A target molecule is present at low concentration in a large aqueous broth. Which strategy can reduce volume before final purification?
A repeat the inoculation
B discard the permeate without testing
C membrane concentration or another validated concentration step
D add more water
Answer: C. membrane concentration or another validated concentration step. Concentrating dilute product streams can reduce the volume handled in later purification steps.
An immobilized enzyme has strong activity on the bead surface but poor conversion inside large beads. Which mechanism is plausible?
A diffusion limitation within the support
B chromosome segregation
C pollen incompatibility
D antibody cross-reactivity
Answer: A. diffusion limitation within the support. Substrate diffusion into porous supports can limit the observed activity of immobilized enzymes.
A plant raises feed flow through a fixed-volume continuous reactor. What happens to the nominal residence time?
A it remains unchanged for every flow rate
B it increases in direct proportion to flow
C it decreases
D it becomes equal to product titer
Answer: C. it decreases. Residence time is reactor volume divided by flow, so increasing flow reduces residence time.
A cellulosic hydrolysate contains fermentable sugars and inhibitory compounds. Which process decision best balances conversion and cell performance?
A add more inhibitor to increase yield
B discard all sugars before inoculation
C maximize pretreatment severity without testing fermentation
D optimize pretreatment and consider conditioning the hydrolysate before fermentation
Answer: D. optimize pretreatment and consider conditioning the hydrolysate before fermentation. Process development balances sugar release with inhibitor generation and the tolerance of the production strain.
A target product is secreted into broth, while cells remain intact. Which harvest train is most logical?
A add inoculum to the purified product
B remove cells, then concentrate and purify the clarified liquid
C lyse the cells first and discard the supernatant
D distill the exhaust gas before sampling broth
Answer: B. remove cells, then concentrate and purify the clarified liquid. An extracellular product is recovered from the liquid after cell clarification.
A soluble enzyme loses activity during repeated reuse, but immobilization allows recovery after each cycle. Which metric best compares the two processes?
A the initial activity alone
B the number of reactor windows
C cumulative product made per enzyme cost over the catalyst lifetime
D the enzyme label color
Answer: C. cumulative product made per enzyme cost over the catalyst lifetime. Operational lifetime and total product per enzyme cost capture the value of reuse.
A downstream train has clarification recovery 90%, concentration recovery 80%, and polishing recovery 75%. What is the overall recovery?
A 90%
B 54%
C 245%
D 75%
Answer: B. 54%. Multiply the recoveries: 0.90 × 0.80 × 0.75 = 0.54, or 54%.
A liquid-liquid extraction step is being considered for a product that partitions strongly into an immiscible solvent. Which property supports this choice?
A the product ability to replicate DNA
B the shape of the fermenter impeller
C the presence of an antibiotic marker
D a favorable distribution of product between the broth and extraction solvent
Answer: D. a favorable distribution of product between the broth and extraction solvent. Extraction can recover a product when it partitions preferentially into a separate solvent phase.
A cell-free enzyme reactor avoids cell removal, but the product is mixed with substrate and side products. What remains necessary?
A downstream separation and purification
B inoculum preparation
C embryo transfer
D gene knockout
Answer: A. downstream separation and purification. Cell-free reactions still produce mixtures that require product recovery and purification.
A batch process gives lower daily output than a continuous process at similar product concentration. Which factor may explain the difference?
A the absence of substrate in batch operation
B loss of all catalyst in the continuous system
C nonproductive turnaround time between batches
D a change in product molecular weight
Answer: C. nonproductive turnaround time between batches. Batch turnaround, cleaning, filling, and sterilization can reduce productive time per day.
An immobilized catalyst column shows channeling, with liquid bypassing much of the support. What is the likely impact?
A conversion of enzyme into substrate
B increased residence time for every fluid element
C reduced effective contact and conversion
D automatic improvement in product purity
Answer: C. reduced effective contact and conversion. Channeling causes uneven flow and can reduce catalyst utilization and conversion.
An industrial enzyme loses activity after a cleaning cycle. Which development objective is most relevant?
A retain catalytic activity while meeting cleaning and process requirements
B maximize the number of labels on the tank
C remove every control sensor
D increase product dilution
Answer: A. retain catalytic activity while meeting cleaning and process requirements. Industrial operation requires an enzyme that remains active under the actual reaction and cleaning conditions.
A process team compares two routes for the same product. Route A has higher titer but much lower recovery and more energy use. What should guide the decision?
A the reactor exterior color
B overall process economics and product quality across all stages
C the number of upstream samples only
D titer alone
Answer: B. overall process economics and product quality across all stages. A higher titer does not ensure a better process if recovery, energy, or product quality is worse.
A fermentation feed contains 60 kg fermentable sugar per 100 kg feedstock. The process consumes 80% of that sugar. How much sugar is consumed?
A 20 kg
B 80 kg
C 48 kg
D 60 kg
Answer: C. 48 kg. The feed contains 60 kg sugar; 0.80 × 60 = 48 kg is consumed.
A reactor produces 240 kg product in 12 hours at 4 m³ working volume. What is average volumetric productivity?
A 5 kg m⁻³ h⁻¹
B 48 kg m⁻³ h⁻¹
C 20 kg m⁻³ h⁻¹
D 0.2 kg m⁻³ h⁻¹
Answer: A. 5 kg m⁻³ h⁻¹. Productivity = 240 kg ÷ (4 m³ × 12 h) = 5 kg m⁻³ h⁻¹.
A sterile production line repeatedly fails contamination checks after a transfer step. What should be reviewed first?
A the waste label font
B aseptic connectors, transfer sterilization, and boundary integrity
C the enzyme amino-acid sequence only
D the product market price only
Answer: B. aseptic connectors, transfer sterilization, and boundary integrity. Contamination after transfer points to a possible breach in aseptic connections or sterilization.
A bioreactor at production scale overheats despite correct temperature at the inlet. What engineering limitation should be examined?
A heat-transfer capacity relative to metabolic heat generation
B the label on the cooling line
C the antibody binding affinity
D the gene sequence of the product
Answer: A. heat-transfer capacity relative to metabolic heat generation. Large-scale reactors must remove metabolic heat at a rate that matches heat generation.
A downstream filter retains cells but lets a small soluble product pass into the filtrate. Where should recovery focus?
A the retained biomass only
B the exhaust air
C the inoculum flask
D the filtrate
Answer: D. the filtrate. If the product is extracellular and passes the filter, it will be in the filtrate.
A process makes an intracellular enzyme and a secreted by-product. Which harvest strategy should be considered first?
A separate cells from broth, then recover the intracellular enzyme from biomass
B distill the exhaust gas
C add more feed after harvest
D discard cells and purify only broth
Answer: A. separate cells from broth, then recover the intracellular enzyme from biomass. The intracellular target is associated with biomass and requires cell disruption, while the soluble by-product remains in broth.
A scale-up plan keeps impeller tip speed constant but oxygen transfer becomes insufficient. What is the better design approach?
A measure and optimize oxygen transfer and mixing at the larger scale
B assume constant tip speed guarantees identical kLa
C increase vessel size without monitoring
D remove the aeration system
Answer: A. measure and optimize oxygen transfer and mixing at the larger scale. A single scale-up criterion does not guarantee equal oxygen transfer; relevant process metrics must be measured.
A continuous immobilized-enzyme column shows pressure drop increasing over time. Which operational problem should be examined?
A loss of the feedstock’s chromosome
B fouling or channel blockage in the bed
C gene knockout in the enzyme
D excessive pollen production
Answer: B. fouling or channel blockage in the bed. Fouling or solids accumulation can increase pressure drop and disrupt flow through a packed bed.
For a product made by a cell-free enzyme reactor, which stage is still necessary?
A hybridoma selection
B plant acclimatization
C embryo transfer
D downstream recovery and purification
Answer: D. downstream recovery and purification. Cell-free production still yields a reaction mixture that must be separated and purified.
A process design minimizes product loss by measuring concentration after each recovery step. What can be calculated from those measurements?
A the patient’s antibody titer
B stepwise and overall recovery yield
C the organism’s taxonomy only
D the promoter’s tissue specificity
Answer: B. stepwise and overall recovery yield. Mass balances across each unit operation quantify recovery and identify major losses.
A plant wants to replace a petroleum-derived intermediate with a fermentation product. Which comparison is essential before industrial adoption?
A only the microbe’s cell shape
B only the color of fermentation broth
C the number of operator badges
D yield, productivity, feedstock cost, recovery cost, and product specification
Answer: D. yield, productivity, feedstock cost, recovery cost, and product specification. Economic and technical feasibility depends on production performance, feedstock, separation, and product quality.