A friction clutch transmits torque through what?
A Gear teeth only
B Hydraulic pressure alone
C Friction surfaces
D Magnetic flux only
Answer: C. Friction surfaces. Clutch friction plates transfer torque when clamped together.
A multi-plate clutch increases capacity by adding what?
A Gear ratios
B Shaft length
C Friction interfaces
D Differential gears
Answer: C. Friction interfaces. More active friction interfaces increase torque capacity for similar size.
A synchromesh unit equalizes speeds before what engagement?
A Brake shoes
B Gear teeth
C Tire treads
D Engine valves
Answer: B. Gear teeth. Synchronizers match gear and shaft speed to enable smooth engagement.
A manual gearbox provides multiple what?
A Gear ratios
B Suspension rates
C Brake circuits
D Fuel pressures
Answer: A. Gear ratios. Selectable gear ratios match engine speed and torque to vehicle demand.
An overdrive gear gives output speed relative to input what?
A Higher speed
B Lower speed always
C Zero speed
D Same torque always
Answer: A. Higher speed. Overdrive reduces engine speed relative to road speed in cruising.
A numerically higher gear ratio generally provides what?
A Higher road speed
B Less torque always
C More wheel torque
D No speed change
Answer: C. More wheel torque. A larger reduction ratio multiplies torque while reducing output speed.
A torque converter transmits torque using what medium?
A Engine coolant
B Transmission fluid
C Air only
D Grease only
Answer: B. Transmission fluid. A torque converter transfers torque hydrodynamically through fluid.
A torque-converter lockup clutch reduces what at cruise?
A Engine compression
B Slip losses
C Tire rolling resistance
D Brake pressure
Answer: B. Slip losses. Lockup mechanically couples input and output to reduce converter slip.
An open differential allows left and right wheels to do what?
A Receive different brake fluid
B Steer independently always
C Turn at different speeds
D Rotate opposite always
Answer: C. Turn at different speeds. Differential gearing permits relative wheel rotation during cornering.
A limited-slip differential restricts excessive what?
A Engine oil flow
B Brake pedal travel
C Steering angle
D Wheel-speed difference
Answer: D. Wheel-speed difference. LSD mechanisms limit wheel-speed difference and can improve traction.
A universal joint accommodates what between shafts?
A Only axial compression
B Gear backlash
C Brake wear
D Angular misalignment
Answer: D. Angular misalignment. Universal joints transmit torque between intersecting shafts at an angle.
A constant-velocity joint is designed to maintain what?
A Zero shaft torque
B Fixed wheel position
C Brake pressure
D Uniform angular speed
Answer: D. Uniform angular speed. CV joints transmit rotation smoothly at changing shaft angles.
A transfer case distributes torque in what drivetrain?
A Front-wheel drive only
B Rear-wheel drive only
C Four-wheel drive
D Bicycle drive
Answer: C. Four-wheel drive. A transfer case routes power to front and rear axles in 4WD systems.
A hypoid final drive uses what shaft arrangement?
A Offset intersecting axes
B Coaxial shafts
C Parallel belt drives
D Flexible cable only
Answer: A. Offset intersecting axes. Hypoid gears have offset, nonintersecting axes.
A half-shaft transmits torque from differential to what?
A Driven wheel
B Steering wheel
C Transmission input
D Clutch pedal
Answer: A. Driven wheel. Half-shafts connect the differential to individual driven wheels.
A rear-wheel-drive layout commonly uses what long shaft?
A CVT belt only
B Camshaft
C Steering column
D Propeller shaft
Answer: D. Propeller shaft. The propeller shaft carries transmission output to the rear differential.
A continuously variable transmission provides what ratio behavior?
A Continuously changing ratio
B Fixed steps only
C No torque transfer
D Reverse ratio only
Answer: A. Continuously changing ratio. A CVT varies transmission ratio continuously over a range.
A belt CVT varies ratio by changing what?
A Gear tooth count
B Clutch plate number
C Tire radius
D Pulley effective diameters
Answer: D. Pulley effective diameters. Variable pulley sheaves change belt operating radius.
A clutch release bearing acts when the clutch is what?
A Disengaged
B Fully engaged
C Overheated only
D In reverse gear
Answer: A. Disengaged. The release bearing transfers pedal force to the clutch diaphragm or release mechanism.
A flywheel smooths engine torque pulsations by storing what?
A Brake fluid
B Fuel pressure
C Rotational energy
D Steering force
Answer: C. Rotational energy. The flywheel stores energy between combustion events.
Transmission lubrication reduces friction and what?
A Gear ratio
B Wear
C Wheelbase
D Tire slip always
Answer: B. Wear. Lubricant forms films that reduce wear and carry heat away.
A synchronizer cone uses friction to do what?
A Increase tire grip
B Match rotational speeds
C Press brake shoes
D Cool gearbox oil
Answer: B. Match rotational speeds. Cone friction speeds or slows gear components before locking engagement.
A gear selector fork moves which component?
A Differential housing
B Sliding sleeve
C Clutch disc
D Brake piston
Answer: B. Sliding sleeve. The selector fork shifts a sleeve or gear to engage a ratio.
A differential pinion meshes with which gear?
A Ring gear only
B Clutch plate
C Input shaft
D Side gear
Answer: D. Side gear. Spider pinions mesh with side gears attached to axle shafts.
A ring-and-pinion set changes direction and what?
A Final-drive ratio
B Suspension travel
C Brake pressure
D Engine valve lift
Answer: A. Final-drive ratio. The ring and pinion provide final reduction and redirect torque to the axle.