A GNSS point has open sky but nearby glass buildings. Main risk?
A Contour interpolation
B Map scale error
C Multipath error
D Photo parallax only
Answer: C. Multipath error. Reflections from nearby surfaces can create delayed GNSS signals and position bias.
Satellite geometry is poor when satellites cluster in…
A One part of sky
B Evenly spread directions
C Opposite sky sectors
D A wide elevation range
Answer: A. One part of sky. Poorly distributed satellites increase dilution of precision and weaken the position solution.
Ionospheric delay affects GNSS signals as they pass through…
A The geoid surface
B Charged upper atmosphere
C The receiver tripod
D A map projection
Answer: B. Charged upper atmosphere. The ionosphere is dispersive and delays satellite signals, with effects depending on frequency and conditions.
Differential GNSS corrections work best when errors are…
A Independent across nearby sites
B Only due to map scale
C Similar at base and rover
D Caused by imagery
Answer: C. Similar at base and rover. Nearby receivers observe many common satellite and atmospheric errors that can be reduced by differencing.
Carrier-phase RTK achieves precision by resolving…
A Integer ambiguities
B Image pixel labels
C Map contour intervals
D Laser intensity classes
Answer: A. Integer ambiguities. RTK uses carrier-phase observations and must resolve integer cycle ambiguities.
A vertical height from GNSS needs a geoid model to relate ellipsoidal height to…
A Orthometric height
B Map scale
C Pixel brightness
D Slope distance
Answer: A. Orthometric height. Geoid separation helps convert ellipsoidal height to an elevation related to mean sea level.
A coordinate layer plotted in the wrong datum may show…
A Higher pixel resolution
B More contour lines
C Lower steel stress
D Systematic positional offset
Answer: D. Systematic positional offset. Datum mismatch can shift all mapped features systematically.
An optical satellite image under thick clouds may have…
A Perfect terrain visibility
B Missing surface information
C No atmospheric effect
D A direct subsurface view
Answer: B. Missing surface information. Clouds obscure the ground in optical imagery.
Radar imagery can often observe through…
A Solid bedrock
B Buildings underground
C All vegetation layers
D Cloud cover
Answer: D. Cloud cover. Microwave radar is less affected by cloud cover than optical imaging, though other effects remain.
Stereo photogrammetry estimates depth from…
A Parallax between views
B Map legend symbols
C A single brightness value
D GNSS clock bias
Answer: A. Parallax between views. The apparent displacement of features between overlapping images provides depth information.
Poor ground-control distribution can cause…
A Better absolute accuracy
B More satellite signals
C A stronger laser return
D Warped image products
Answer: D. Warped image products. Control clustered in one area may leave distortion elsewhere weakly constrained.
Checkpoints used for accuracy assessment should be…
A Independent of model fitting
B The same fitting points only
C Generated from the output
D Chosen after seeing errors
Answer: A. Independent of model fitting. Independent checkpoints avoid optimistic accuracy estimates from reused control points.
A LiDAR ground-classification error can distort…
A GNSS satellite time
B Map projection datum
C Attribute table names
D Bare-earth elevation model
Answer: D. Bare-earth elevation model. Misclassified vegetation or structures can contaminate a terrain model.
A digital surface model is preferable for…
A Bare-earth slope stability only
B Building-height analysis
C Underground aquifer mapping
D Subsurface fault depth
Answer: B. Building-height analysis. A DSM retains roofs and canopy surfaces needed for height and urban form analysis.
A digital terrain model is preferable for…
A Roof clearance only
B Ground-slope analysis
C Tree crown height
D Satellite signal strength
Answer: B. Ground-slope analysis. A bare-earth terrain model supports terrain slope and drainage analysis.
GIS topology rules can detect…
A Gaps and overlaps
B Satellite orbit errors
C Sensor spectral bands
D Steel fatigue cracks
Answer: A. Gaps and overlaps. Topology checks identify invalid spatial relationships such as gaps, overlaps or disconnected lines.
For parcel area comparison, use a projection designed to preserve…
A All distances everywhere
B Every direction simultaneously
C Area
D All shapes everywhere
Answer: C. Area. Equal-area projections preserve area, though they distort other map properties.
Repeated reprojection of raster data can…
A Create new field observations
B Resample and alter cell values
C Improve source accuracy
D Remove all measurement error
Answer: B. Resample and alter cell values. Raster reprojection estimates values on a new grid and can introduce interpolation effects.
Accuracy differs from precision because accuracy describes…
A Repeatability only
B Pixel count
C Closeness to true value
D Map scale only
Answer: C. Closeness to true value. Accuracy is closeness to the reference truth; precision concerns repeatability or dispersion.
A geospatial layer without CRS metadata risks…
A Higher resolution
B Automatic correction
C Incorrect placement and analysis
D Lower storage only
Answer: C. Incorrect placement and analysis. Without a defined coordinate reference system, coordinates may be interpreted incorrectly.
A multi-temporal image comparison should control…
A Only file names
B Season and acquisition conditions
C Map title font
D Road label color
Answer: B. Season and acquisition conditions. Season, illumination, atmosphere and sensor conditions can confound change detection.
InSAR can estimate surface change from…
A Optical color only
B Survey tape lengths
C Contour labels
D Radar phase differences
Answer: D. Radar phase differences. Interferometric SAR compares radar phase to measure line-of-sight surface displacement.
An orthomosaic joins images after…
A Geometric correction and mosaicking
B Manual color painting only
C Deleting all control points
D Changing GNSS frequency
Answer: A. Geometric correction and mosaicking. Orthomosaics combine corrected image tiles into a consistent map-like product.
Quality reporting for a survey should include…
A Only final map colors
B Only file size
C Accuracy and methods
D Only instrument brand
Answer: C. Accuracy and methods. Useful quality reports document methods, reference system, control and achieved accuracy.
A mapping workflow should preserve…
A Only final screenshots
B No metadata
C Only manually edited output
D Raw data and processing history
Answer: D. Raw data and processing history. Retaining source data and processing steps supports traceability and reproducibility.