Difficulty: Easy & Basic
Warm, humid climates generally favour rapid chemical weathering because they provide:
A Only low temperatures
B No liquid water
C Constantly frozen ground
D Heat and abundant water
Answer: D. Heat and abundant water. Many chemical reactions proceed faster with heat and water.
Physical weathering can accelerate chemical weathering by:
A Increases exposed surface area
B Removing all fractures
C Stopping water flow
D Preventing minerals from reacting
Answer: A. Increases exposed surface area. Breaking rock into smaller pieces exposes more surface for chemical reactions.
A joint in bedrock is:
A Fracture without major displacement
B A fold hinge
C A river channel
D A volcanic vent
Answer: A. Fracture without major displacement. Joints are fractures in rock that provide pathways for water and weathering.
Differential weathering produces uneven relief because:
A Uniform weathering rates
B Erosion stops everywhere
C Unequal rock resistance
D Climate has no effect
Answer: C. Unequal rock resistance. More resistant rocks remain as ridges or knobs while weaker material is removed faster.
A well-jointed rock often weathers faster than an otherwise similar massive rock because joints:
A Prevent chemical reactions
B Remove all mineral grains
C Admit water and air
D Stop frost action
Answer: C. Admit water and air. Fractures expose more rock surface to water, air, and temperature changes.
Spheroidal weathering commonly rounds blocks as:
A Rock melts internally
B River moves the outcrop
C Corners weather fastest
D Wind covers every side
Answer: C. Corners weather fastest. Water reaches corners from several directions, rounding joint-bounded blocks.
A talus slope is an accumulation of:
A Rounded delta sand
B Coral fragments on a reef
C Windblown floodplain clay
D Angular fragments beneath cliffs
Answer: D. Angular fragments beneath cliffs. Rockfall debris commonly collects as angular talus at the base of a cliff.
A rotational slide along a curved failure plane is commonly called a:
A Rock glacier
B Dune
C Delta
D Slump
Answer: D. Slump. A slump is a rotational slide moving along a curved surface.
A translational landslide commonly moves:
A Only upward
B Circular path around crater
C As dissolved ions in groundwater
D Along a relatively planar surface
Answer: D. Along a relatively planar surface. Translational slides move along a roughly planar weakness or bedding surface.
A debris flow is especially likely after intense rain on:
A A calm deep-ocean basin
B A flat, dry bedrock plateau
C Stable unmelted ice sheet
D Steep slopes with loose sediment
Answer: D. Steep slopes with loose sediment. Heavy rainfall can saturate loose debris and trigger rapid downslope flows.
The angle of repose is the:
A Dip of Earthβs axis
B Slope of every glacier
C River-mouth angle
D Steepest stable debris angle
Answer: D. Steepest stable debris angle. Loose particles remain stable only up to a characteristic slope angle.
A riverβs competence refers to its ability to:
A Transport a given grain size
B Create volcanic ash
C Dissolve every mineral
D Carry a fixed yearly load
Answer: A. Transport a given grain size. Competence is the largest particle size a stream can move.
A riverβs capacity refers to the:
A Largest single boulder only
B Chemical hardness of its water
C Total transportable sediment load
D Depth of its source spring
Answer: C. Total transportable sediment load. Capacity is the total quantity of sediment a stream can carry.
As a streamβs velocity decreases, it commonly begins to:
A Deposit its coarser load
B Increase its competence
C Lift larger boulders
D Dissolve all channel banks
Answer: A. Deposit its coarser load. Lower transport energy often causes sediment to settle, beginning with coarser particles.
A meandering river erodes most strongly on the:
A Inner point bar
B Outer bank of a bend
C Centre of a lake
D Top of the floodplain only
Answer: B. Outer bank of a bend. Higher velocity along the outer bank causes lateral erosion.
A point bar forms mainly on the:
A Outer bank of a meander
B Inner bank of a meander
C Windward side of a dune
D Crest of a mountain
Answer: B. Inner bank of a meander. Lower velocity on the inside of a bend encourages deposition and point-bar growth.
Wind transports sand mainly by saltation when grains:
A Roll only under glaciers
B Move only as suspended clay
C Hop near the ground
D Remain dissolved in water
Answer: C. Hop near the ground. Saltation is the short hopping motion of sand grains driven by wind.
Loess consists chiefly of:
A Wind-deposited silt
B Marine limestone
C Glacial boulders
D Volcanic lava
Answer: A. Wind-deposited silt. Loess is a blanket of windblown silt deposited over land.
A glacial moraine is made mainly of:
A Dissolved minerals
B Well-sorted river sand only
C Unsorted sediment deposited by ice
D Windblown loess only
Answer: C. Unsorted sediment deposited by ice. Glaciers deposit till and other debris as moraines.
A U-shaped valley is most commonly carved by:
A A glacier
B Wind deflation
C A meandering river
D A lava dome
Answer: A. A glacier. Glacial erosion widens and deepens valleys, producing a characteristic U-shaped cross section.
Wave-cut cliffs and platforms result largely from:
A Coastal erosion by waves
B Glacial plucking on land
C Wind deposition of loess
D Chemical weathering by roots only
Answer: A. Coastal erosion by waves. Wave attack erodes a notch at the shoreline and can leave a retreating cliff and platform.
Vegetation reduces soil erosion mainly by:
A Making slopes steeper
B Binding soil and slowing runoff
C Increasing raindrop impact
D Removing all infiltration
Answer: B. Binding soil and slowing runoff. Roots stabilize soil and plant cover reduces runoff velocity and raindrop impact.
A steep slope with saturated soil is more prone to landsliding because water can:
A Make all rocks stronger
B Add weight, reduce friction
C Cement grains instantly
D Remove gravity
Answer: B. Add weight, reduce friction. Water adds weight and can raise pore pressure, reducing resistance to sliding.
Which human activity can increase slope instability?
A Improving drainage carefully
B Clear vegetation or cut slopes
C Planting deep-rooted cover
D Reducing slope angle
Answer: B. Clear vegetation or cut slopes. Vegetation removal and poorly designed cuts can reduce slope stability.
A floodplain is built mainly by:
A Wind abrasion on a ridge
B Repeated river overbank deposition
C Glacial plucking
D Chemical dissolution of granite
Answer: B. Repeated river overbank deposition. Floodwaters spread sediment across adjacent lowlands and build floodplains over time.