Answer: D. [M L⁻¹ T⁻¹]. Dynamic viscosity is shear stress divided by velocity gradient. Their dimensions give (M L⁻¹ T⁻²)/(T⁻¹) = M L⁻¹ T⁻¹.
A cube has an edge length of 2.00 cm. What is its volume with appropriate significant figures?
A 8.00 cm³
B 8 cm³
C 4.00 cm³
D 6.00 cm³
Answer: A. 8.00 cm³. Volume = (2.00 cm)³ = 8.00 cm³. The measured edge has three significant figures, so the volume is reported to three.
A vernier caliper reads 2.3 cm on the main scale. Its 6th vernier division coincides, and its least count is 0.01 cm. What is the reading?
A 2.30 cm
B 2.06 cm
C 2.36 cm
D 2.60 cm
Answer: C. 2.36 cm. Reading = main-scale reading + (coinciding division × least count) = 2.30 + 6 × 0.01 = 2.36 cm.
A screw gauge has a 1.0 mm pitch and 100 divisions. The sleeve reads 5.50 mm and the circular scale reads 28 divisions. If the zero error is +0.03 mm, what is the corrected reading?
A 5.78 mm
B 5.75 mm
C 5.53 mm
D 5.81 mm
Answer: B. 5.75 mm. Least count = 1.0/100 = 0.01 mm. Observed reading = 5.50 + 28(0.01) = 5.78 mm. Subtract the positive zero error: 5.78 − 0.03 = 5.75 mm.
What are the dimensions of surface tension, defined as force per unit length?
A [M T⁻²]
B [M L T⁻²]
C [M L⁻¹ T⁻¹]
D [M L⁻¹ T⁻²]
Answer: A. [M T⁻²]. Surface tension = force/length. Dividing M L T⁻² by L gives M T⁻².
What are the dimensions of thermal conductivity k, whose SI unit is W m⁻¹ K⁻¹?
A [M L² T⁻³ Θ⁻¹]
B [M T⁻³ Θ⁻¹]
C [M L T⁻² Θ⁻¹]
D [M L T⁻³ Θ⁻¹]
Answer: D. [M L T⁻³ Θ⁻¹]. A watt has dimensions M L² T⁻³. Dividing by length and temperature gives M L T⁻³ Θ⁻¹.
What are the dimensions of electrical resistivity in terms of mass M, length L, time T, and current I?
A [M L² T⁻³ I⁻²]
B [M L³ T⁻³ I⁻²]
C [M L³ T⁻² I⁻²]
D [M L T⁻³ I⁻¹]
Answer: B. [M L³ T⁻³ I⁻²]. Resistivity ρ = resistance × length. Since resistance has dimensions M L² T⁻³ I⁻², ρ has dimensions M L³ T⁻³ I⁻².
If velocity is given by v = a tⁿ, where a is acceleration, what must n equal?
A 2
B −1
C 1
D 1/2
Answer: C. 1. Acceleration × timeⁿ has dimensions L Tⁿ⁻². Equating this to velocity L T⁻¹ gives n − 2 = −1, so n = 1.
A pendulum period T depends only on length l and gravitational acceleration g. Which powers make lᵃgᵇ have the dimensions of time?
A a = 1, b = −1
B a = −1/2, b = 1/2
C a = 1/2, b = 1/2
D a = 1/2, b = −1/2
Answer: D. a = 1/2, b = −1/2. The dimensions of lᵃgᵇ are Lᵃ(LT⁻²)ᵇ = Lᵃ⁺ᵇT⁻²ᵇ. Matching T¹ gives b = −1/2 and a + b = 0, so a = 1/2.
In x = at² + bt + c, where x is a length and t is time, what are the dimensions of b?
A [L T⁻¹]
B [L T⁻²]
C [L]
D [T⁻¹]
Answer: A. [L T⁻¹]. Each term in the sum must have dimensions of length. Since bt has dimension L, b must have dimension L T⁻¹.
A quantity Q = mᵃvᵇ has the dimensions of momentum. What are a and b?
A a = 1, b = 2
B a = 0, b = 1
C a = 1, b = 1
D a = 2, b = −1
Answer: C. a = 1, b = 1. Momentum has dimensions M L T⁻¹. Since mᵃvᵇ has dimensions MᵃLᵇT⁻ᵇ, matching powers gives a = 1 and b = 1.
For Q = xy/z, the maximum fractional uncertainties in x, y, and z are 2%, 3%, and 1%. What is the maximum percentage uncertainty in Q?
A 2%
B 6%
C 4%
D 5%
Answer: B. 6%. For a product divided by a measured quantity, maximum fractional uncertainties add: 2% + 3% + 1% = 6%.
A cylinder’s measured diameter has 1% uncertainty and its height has 2% uncertainty. What is the approximate maximum percentage uncertainty in its volume?
A 4%
B 2%
C 3%
D 5%
Answer: A. 4%. V = πd²h/4, so the fractional uncertainty is approximately 2(1%) + 2% = 4%.
A rectangle has sides 10.0 ± 0.1 cm and 5.0 ± 0.1 cm. What is the approximate percentage uncertainty in its area?
A 1%
B 2%
C 4%
D 3%
Answer: D. 3%. The area is 50.0 cm². Its maximum absolute uncertainty is approximately 5.0(0.1) + 10.0(0.1) = 1.5 cm², or 1.5/50.0 × 100% = 3%.
A length is calculated from x = 12.4 ± 0.2 cm and y = 5.1 ± 0.1 cm as x + y. What result and maximum absolute uncertainty should be reported?
A 17.5 ± 0.1 cm
B 17.5 ± 0.2 cm
C 17.5 ± 0.3 cm
D 7.3 ± 0.3 cm
Answer: C. 17.5 ± 0.3 cm. The central values add to 17.5 cm. For a sum, maximum absolute uncertainties add: 0.2 + 0.1 = 0.3 cm.
Using x = 12.4 ± 0.2 cm and y = 5.1 ± 0.1 cm, what result and maximum absolute uncertainty apply to x − y?
A 7.3 ± 0.1 cm
B 7.3 ± 0.3 cm
C 7.3 ± 0.2 cm
D 17.5 ± 0.3 cm
Answer: B. 7.3 ± 0.3 cm. The central difference is 12.4 − 5.1 = 7.3 cm. For subtraction, maximum absolute uncertainties still add: 0.2 + 0.1 = 0.3 cm.
Evaluate (12.5 × 3.42) / 2.0 and round using the correct significant figures.
A 21
B 21.4
C 21.38
D 20
Answer: A. 21. The unrounded result is 21.375. The least precise factor, 2.0, has two significant figures, so the result is 21.
How many significant figures are in 0.00009050?
A 2
B 3
C 5
D 4
Answer: D. 4. Leading zeros are not significant. The digits 9, 0, 5, and the final 0 are significant, giving four.
Calculate 12.11 + 0.3 and round according to the addition rule for significant figures.
A 12.41
B 12.4
C 12
D 12.1
Answer: B. 12.4. The exact sum is 12.41. The least precise addend is given to the tenths place, so round the result to 12.4.
A rectangle’s sides are measured as 25.0 ± 0.5 cm and 10.0 ± 0.2 cm. What is the approximate maximum percentage uncertainty in its area?
A 2%
B 3%
C 4%
D 5%
Answer: C. 4%. For area, the fractional uncertainties add: (0.5/25.0 + 0.2/10.0) × 100% = 2% + 2% = 4%.
A stopwatch shows 1.25 s at the start and 8.91 s at the finish. What elapsed time is indicated?
A 7.66 s
B 7.6 s
C 7.76 s
D 10.16 s
Answer: A. 7.66 s. Elapsed time = 8.91 s − 1.25 s = 7.66 s. Both readings are to the hundredth of a second.
A sphere has mass 25.0 g and radius 1.00 cm. What is its density to three significant figures?
A 2.39 g/cm³
B 4.19 g/cm³
C 6.25 g/cm³
D 5.97 g/cm³
Answer: D. 5.97 g/cm³. Density = m/V = 25.0 / [(4/3)π(1.00)³] = 5.97 g/cm³ to three significant figures.
An accepted value is 50.0 and a measurement is 49.2. What is the percentage error?
What can dimensional analysis not determine in a physical equation?
A A numerical dimensionless constant
B Whether terms have compatible dimensions
C The dimensions required for a coefficient
D How powers of variables must combine
Answer: A. A numerical dimensionless constant. Dimensional analysis checks dimensional consistency and can infer powers, but it cannot determine a pure numerical dimensionless factor such as 2 or π.
A length is 20.0 ± 0.4 cm. What is the approximate percentage uncertainty in its reciprocal, 1/length?
A 0.5%
B 2%
C 4%
D 20%
Answer: B. 2%. The fractional uncertainty in a reciprocal has the same magnitude as that in the original quantity: (0.4/20.0) × 100% = 2%.