For a simple Watt governor, equilibrium height is what?
A g / omega squared
B omega squared / g
C g omega
D omega / g squared
Answer: A. g / omega squared. The ideal Watt governor relation is h = g/ω².
A Porter governor differs by adding what?
A Hydraulic dashpot only
B Central sleeve load
C Flywheel rim
D Cam follower
Answer: B. Central sleeve load. A Porter governor adds a central load on the sleeve to increase controlling force.
A Hartnell governor uses which controlling element?
A Spring force
B Gravity-only weights
C Hydraulic pressure
D Magnetic flux
Answer: A. Spring force. Hartnell governors use a spring to provide the controlling force.
A governor is called isochronous when what?
A Equilibrium speed is constant
B Sleeve cannot move
C Balls have no mass
D Speed range is maximum
Answer: A. Equilibrium speed is constant. An ideal isochronous governor has the same equilibrium speed at all radii.
A flywheel differs from governor because it controls what?
A Mean speed after load change
B Fuel supply only
C Bearing temperature
D Cyclic speed variation
Answer: D. Cyclic speed variation. A flywheel handles within-cycle speed fluctuation; a governor regulates mean speed with load.
Area under a turning-moment diagram over angle gives what?
A Angular acceleration
B Work done
C Gear tooth force
D Damping ratio
Answer: B. Work done. Torque integrated over angular displacement gives work.
Maximum fluctuation of energy is shown by what?
A Smallest cam lift
B Maximum shaft angle
C Largest area from mean torque
D Largest gear ratio
Answer: C. Largest area from mean torque. The maximum energy fluctuation is the largest algebraic area between torque curve and mean torque line.
A friction clutch transmits torque mainly by what?
A Gear tooth action
B Magnetic attraction
C Frictional contact
D Fluid buoyancy
Answer: C. Frictional contact. Clutch plates transmit torque through friction between engaged surfaces.
For a dry clutch, increasing axial force usually does what?
A Raises torque capacity
B Lowers friction force
C Stops rotation instantly
D Changes plate diameter
Answer: A. Raises torque capacity. Greater normal force increases available friction torque for unchanged surfaces.
Gyroscopic couple magnitude is what?
A I omega Omega
B I alpha squared
C m v squared
D Torque divided inertia
Answer: A. I omega Omega. The gyroscopic couple magnitude is C = IωΩ for spin speed ω and precession Ω.
Gyroscopic precession is rotation of which axis?
A Shaft material axis length
B Crank radius
C Flywheel rim width
D Spin axis direction
Answer: D. Spin axis direction. Precession is the change in direction of a spinning body’s angular momentum axis.
Gyroscopic reaction acts about what relative to spin and precession?
A Parallel to spin only
B Along precession only
C Perpendicular to both
D At their midpoint
Answer: C. Perpendicular to both. The gyroscopic couple direction follows the vector product of angular momentum and precession rate.
Coriolis acceleration arises from motion relative to what?
A Rotating reference frame
B Fixed inertial frame only
C A stationary cam
D A translating belt
Answer: A. Rotating reference frame. Coriolis acceleration appears when relative motion occurs in a rotating frame.
In a cam motion law, jerk is what?
A Derivative of acceleration
B Integral of displacement
C Derivative of lift only
D Integral of velocity
Answer: A. Derivative of acceleration. Jerk is the time derivative of acceleration and affects dynamic smoothness.
A discontinuity in jerk may increase what?
A Static mobility
B Dynamic vibration
C Gear module
D Mean speed only
Answer: B. Dynamic vibration. A jerk discontinuity can excite vibration and elevate dynamic forces.
Damping ratio is actual damping divided by what?
A Natural frequency
B Spring stiffness
C Mass moment
D Critical damping
Answer: D. Critical damping. The damping ratio ζ = c/c_critical.
An underdamped system has damping ratio what?
A Equal to one
B Less than one
C Greater than one
D Exactly zero always
Answer: B. Less than one. Underdamped motion oscillates while its amplitude decays, with ζ < 1.
An overdamped system has damping ratio what?
A Less than one
B Equal to zero
C Equal to one
D Greater than one
Answer: D. Greater than one. An overdamped system returns without oscillating and has ζ > 1.
A critically damped system has damping ratio what?
A Greater than two
B Less than zero
C Equal to one-half
D Equal to one
Answer: D. Equal to one. Critical damping corresponds to ζ = 1 and gives the fastest nonoscillatory return.
For successive same-side peaks, log decrement is what?
A Peak sum divided by time
B Natural log of amplitude ratio
C Frequency times mass
D Stiffness divided by damping
Answer: B. Natural log of amplitude ratio. Logarithmic decrement is ln(x₁/x₂) for successive peak amplitudes.
Torsional shaft stiffness for a uniform shaft is what?
A GL / J
B J / GL
C GJ / L
D G L J
Answer: C. GJ / L. For a uniform circular shaft, torsional stiffness k = GJ/L.
Two torsional shafts in series have equivalent stiffness how?
A Stiffnesses add directly
B Use the larger stiffness
C Reciprocals add
D Use mean stiffness
Answer: C. Reciprocals add. Series shaft twists add, so reciprocal torsional stiffnesses add.
A rotor reaches critical speed near what condition?
A Torque becomes zero
B Mass becomes zero
C Excitation matches natural frequency
D Damping becomes infinite
Answer: C. Excitation matches natural frequency. Critical speed occurs when rotational excitation coincides with a rotor natural frequency.
The coefficient of fluctuation of energy is energy range divided by what?
A Mean torque
B Peak speed
C Flywheel radius
D Work per cycle
Answer: D. Work per cycle. It is the maximum energy fluctuation divided by work done per cycle.
A cam follower with zero acceleration at endpoints reduces what?
A Follower lift
B Impact at transitions
C Cam rotation
D Base-circle radius
Answer: B. Impact at transitions. Smooth endpoint acceleration helps reduce dynamic shock when the follower enters or leaves a rise.