Near what depth does the mantle 410 discontinuity occur?
AAbout 660 kilometres
BAbout 410 kilometres
CAbout 2,900 kilometres
DAbout 5,100 kilometres
Answer: B. About 410 kilometres. The upper mantle commonly has a seismic discontinuity near 410 kilometres depth, linked to a mineral phase transition.
Which transformation is commonly linked to the 410-km discontinuity?
ARingwoodite to bridgmanite
BQuartz to feldspar
COlivine to wadsleyite
DBasalt to granite
Answer: C. Olivine to wadsleyite. At roughly 410 kilometres, olivine transforms into the denser high-pressure mineral wadsleyite.
Which depth range broadly defines the mantle transition zone?
AAbout 410–660 kilometres
BAbout 10–100 kilometres
CAbout 660–2,900 kilometres
DAbout 2,900–5,100 kilometres
Answer: A. About 410–660 kilometres. The mantle transition zone lies between prominent seismic boundaries near 410 and 660 kilometres depth.
Which mineral breakdown is commonly linked to the 660-km boundary?
AOlivine into quartz
BCalcite into magma
CFeldspar into mica
DRingwoodite into two phases
Answer: D. Ringwoodite into two phases. Near 660 kilometres, ringwoodite breaks down into bridgmanite and ferropericlase in the common post-spinel interpretation.
In a cold subducting region, where can the 410 boundary shift?
ATo deeper depth
BTo shallower depth
CIt disappears always
DInto the crust
Answer: B. To shallower depth. The olivine-to-wadsleyite transition occurs at shallower depth in colder mantle conditions.
In a cold subducting region, how can the 660 boundary shift?
ATo greater depth
BTo shallower depth
CInto the crust
DIt becomes horizontal
Answer: A. To greater depth. The post-spinel transition shifts deeper in colder mantle, moving the 660-kilometre boundary downward.
What can opposing 410 and 660 shifts do beneath cold slabs?
ARemove the lower mantle
BThin the crust
CThicken the transition zone
DStop all seismic waves
Answer: C. Thicken the transition zone. Cold mantle can move the 410 upward and the 660 downward, increasing transition-zone thickness.
What can hot upwelling mantle do to transition-zone thickness?
AMake it vanish
BThicken continental crust
CCreate a liquid core
DMake it thinner
Answer: D. Make it thinner. Hot upwellings can deepen the 410 and raise the 660, reducing the vertical thickness of the transition zone.
Which mantle boundary marks entry into the lower mantle?
AThe 660-km boundary
BThe 410-km boundary
CThe Moho
DThe Gutenberg boundary
Answer: A. The 660-km boundary. The 660-kilometre discontinuity marks the transition from the mantle transition zone into the lower mantle.
Why do mineral changes create seismic discontinuities?
AGravity stops acting
BWave speeds change abruptly
CRocks become weightless
DThe crust becomes liquid
Answer: B. Wave speeds change abruptly. Mineral phase changes alter elastic properties and density, producing abrupt changes in seismic-wave speeds.
Which method often detects waves converted at deep boundaries?
AWeather forecasting
BMagnetic surveying
CReceiver-function analysis
DRiver profiling
Answer: C. Receiver-function analysis. Receiver functions analyze converted seismic phases to reveal boundaries beneath seismic stations.
What can transition-zone thickness help estimate?
AOcean salinity
BCrustal rainfall
CWind direction
DMantle temperature patterns
Answer: D. Mantle temperature patterns. Because phase-boundary depths respond to temperature, transition-zone thickness can provide clues to mantle thermal structure.
What is seismic anisotropy?
ASpeed varies by direction
BSpeed stops at depth
CWave speed stays constant
DOnly surface waves travel
Answer: A. Speed varies by direction. Seismic anisotropy means seismic-wave speeds depend on travel direction through an oriented material.
Why may a mineral transition lack a clear seismic boundary?
AIt occurs only in air
BIt removes all pressure
CIts velocity contrast is small
DIt stops mantle motion
Answer: C. Its velocity contrast is small. A mineral phase change may be hard to detect if it produces only a small seismic-velocity or density contrast.
Which high-pressure mineral is abundant through much of the lower mantle?
AWadsleyite
BBridgmanite
CQuartz
DHalite
Answer: B. Bridgmanite. Bridgmanite is the most abundant mineral in Earth’s lower mantle according to mineral-physics research.
Which mineral dominates much of the upper mantle?
ABridgmanite
BFerropericlase
CDiamond
DOlivine
Answer: D. Olivine. Olivine is a major mineral of upper-mantle peridotite before transforming at higher pressures.
Why can the 410 and 660 depths vary from place to place?
AEarth stops rotating
BCrustal rocks evaporate
CTemperature and composition vary
DSeismic stations move
Answer: C. Temperature and composition vary. Local temperature and composition affect mineral stability and the depths of mantle phase boundaries.
Which mineral is stable in much of the transition zone?
ARingwoodite
BQuartz
CCalcite
DHalite
Answer: A. Ringwoodite. Ringwoodite is a high-pressure form of olivine-group material stable within much of the transition zone.
Which change occurs near 520 kilometres in many models?
AOlivine to wadsleyite
BWadsleyite to ringwoodite
CRingwoodite to bridgmanite
DBasalt to granite
Answer: B. Wadsleyite to ringwoodite. A discontinuity near 520 kilometres is commonly associated with wadsleyite transforming into ringwoodite.
What chiefly drives olivine’s high-pressure transformations?
ADaily sunlight
BOcean tides
CWind erosion
DIncreasing pressure
Answer: D. Increasing pressure. Pressure increases with depth and stabilizes denser mineral structures within the mantle.
What is the D-double-prime region?
ALowermost mantle above core
BUpper crust beneath soil
CA layer inside inner core
DThe top of the crust
Answer: A. Lowermost mantle above core. The D-double-prime region is the lowermost mantle above the core–mantle boundary and has complex seismic structure.
What is a major use of seismic reflections from mantle boundaries?
AMeasuring ocean waves
BTracking rainfall
CMapping deep interfaces
DFinding wind fronts
Answer: C. Mapping deep interfaces. Reflected seismic energy helps map abrupt interfaces inside Earth that cannot be observed directly.
Aligned olivine in the mantle can provide evidence of what?
AOcean-floor sedimentation
BPast deformation and flow
CAtmospheric circulation
DCore solidification only
Answer: B. Past deformation and flow. Preferred olivine alignment creates anisotropy and can record deformation and flow in the upper mantle.
Which boundary is much deeper than the 660-km discontinuity?
AMoho
BConrad discontinuity
C410-km discontinuity
DCore–mantle boundary
Answer: D. Core–mantle boundary. The core–mantle boundary is far below the transition zone, near 2,900 kilometres depth.
Which rock sample can bring upper-mantle material to the surface?
AMantle xenolith
BRiver cobble
CCoral fragment
DCoal seam
Answer: A. Mantle xenolith. Some volcanic rocks carry mantle xenoliths, providing samples of upper-mantle material for laboratory study.