For a prismatic bar in axial tension, elongation is proportional to load and what?
A Length
B Area squared
C Density
D Poisson ratio
Answer: A. Length. Axial deformation delta = PL/(AE), so it increases with load and length.
For a solid circular shaft, polar moment J equals what?
A πd² / 4
B πd³ / 16
C πd⁴ / 64
D πd⁴ / 32
Answer: D. πd⁴ / 32. The polar second moment of a solid circular section is pi d^4/32.
For a hollow circular shaft, torsional rigidity depends on which difference?
A Outer and inner fourth powers
B Outer and inner diameters sum
C Wall thickness only
D Mean radius squared
Answer: A. Outer and inner fourth powers. J = pi(do^4 – di^4)/32 for a hollow circular section.
A bending moment produces maximum normal stress at what location?
A Extreme fibres
B Neutral axis
C Centroid only
D Beam supports always
Answer: A. Extreme fibres. Bending stress magnitude grows with distance from the neutral axis and peaks at the extreme fibres.
Pure bending has what internal force condition over the section?
A Constant bending moment
B Only axial tension
C Zero moment
D Variable torque only
Answer: A. Constant bending moment. Pure bending is an ideal region with constant moment and zero shear force.
The neutral axis passes through the centroid for what cross-section condition?
A Any composite section
B Homogeneous elastic section
C Any nonlinear material
D Only a hollow shaft
Answer: B. Homogeneous elastic section. For a homogeneous linear-elastic beam under pure bending, the neutral axis passes through the centroid.
The isotropic elastic relation among E, G and nu is what?
A E=G(1+2nu)
B G=E(1+nu)
C E=nu/G
D E=2G(1+nu)
Answer: D. E=2G(1+nu). This relation follows from isotropic linear elasticity.
A plane-stress element has which out-of-plane normal stress approximately zero?
A Sigma z
B Sigma x
C Sigma y
D Tau xy
Answer: A. Sigma z. Plane stress assumes sigma-z and out-of-plane shear stresses are negligible.
Principal planes carry what in-plane shear stress?
A Maximum shear
B Yield stress
C Zero
D Torsion only
Answer: C. Zero. By definition, principal planes have zero shear traction.
For plane stress, maximum in-plane shear is related to principal stresses how?
A Their sum
B Half their difference
C Their product
D Their average squared
Answer: B. Half their difference. Maximum in-plane shear magnitude is (sigma1 – sigma2)/2.
Euler’s pinned-pinned column has effective length equal to what?
A Actual length
B Half the actual length
C Twice the actual length
D One-quarter length
Answer: A. Actual length. For pinned ends, the effective length factor is one.
A short compression member is more likely to fail by what?
A Elastic buckling first
B Shear-lag only
C Material crushing
D Torsional resonance
Answer: C. Material crushing. Short columns generally reach material strength before elastic buckling.
Strain energy is energy stored due to what?
A Rigid translation only
B Temperature alone
C Elastic deformation
D Mass flow
Answer: C. Elastic deformation. Elastic deformation stores strain energy in the material.
Castigliano’s theorem can obtain displacement by differentiating strain energy with respect to what?
A Material density
B Beam width only
C Applied load
D Poisson ratio
Answer: C. Applied load. For linear elastic systems, displacement in a load direction is the derivative of strain energy with respect to that load.
A simply supported beam with central point load has maximum deflection at what location?
A At a support
B One-quarter span always
C Outside the beam
D Midspan
Answer: D. Midspan. For a symmetric central load and support arrangement, maximum deflection occurs at midspan.
A simply supported beam under uniform load has maximum moment at what location?
A At either support
B One-quarter span
C Midspan
D Everywhere equally
Answer: C. Midspan. Under a symmetric uniform load, maximum bending moment occurs at the centre.
A bar fully restrained against thermal expansion develops what under heating?
A Zero stress
B Tensile stress always
C Shear stress only
D Compressive stress
Answer: D. Compressive stress. Restraint prevents free expansion, producing compression when the bar is heated.
Principal strain directions are associated with what strain component?
A Maximum normal stress only
B Zero normal strain
C Infinite shear strain
D Zero engineering shear strain
Answer: D. Zero engineering shear strain. At principal strain directions the transformed engineering shear strain is zero.
The neutral axis separates tensile bending stress from what?
A Thermal strain
B Compressive bending stress
C Shear modulus
D Plastic zone always
Answer: B. Compressive bending stress. On opposite sides of the neutral axis, longitudinal bending stresses have opposite signs.
Fatigue failure is associated with repeated what?
A One static load only
B Uniform temperature only
C Cyclic loading
D No stress variation
Answer: C. Cyclic loading. Repeated or fluctuating stress cycles can cause fatigue cracking below static strength.
Creep is time-dependent deformation under sustained what?
A Only changing speed
B Zero load
C Pure impact
D Stress and temperature
Answer: D. Stress and temperature. Creep is gradual deformation under sustained stress, especially at elevated temperature.
A stress-strain curve’s elastic slope in uniaxial tension is what?
A Young’s modulus
B Poisson ratio
C Toughness
D Resilience only
Answer: A. Young’s modulus. The initial linear slope of normal stress versus normal strain is Young’s modulus.
In bending, shear flow is proportional to VQ divided by what?
A E
B I
C G
D Area squared
Answer: B. I. Beam shear stress uses tau = VQ/(I b), where shear flow is VQ/I.
The flexural rigidity of a beam is the product of E and what?
A Area A
B I
C Polar moment J only
D Poisson ratio
Answer: B. I. Flexural rigidity is EI.
A stress concentration is commonly caused by what geometry?
A Uniform smooth bar
B Notch or hole
C Constant diameter only
D Pure axial loading alone
Answer: B. Notch or hole. Geometric discontinuities such as notches and holes raise local stress.