How many covalent bonds can a silicon atom typically form in a crystal?
A One
B Four
C Two
D Eight
Answer: B. Four. A silicon atom has four valence electrons and typically forms four covalent bonds with neighboring atoms.
Which statement about germanium as an elemental semiconductor is correct?
A Each atom has one valence electron
B It has no valence electrons
C Each atom has four valence electrons
D It is a group-15 element with five valence electrons
Answer: C. Each atom has four valence electrons. Germanium is in group 14, like silicon, and has four valence electrons.
What happens when phosphorus is added in a small amount to silicon?
A It acts as an acceptor and produces p-type material
B It removes all conduction electrons
C It makes the silicon intrinsically pure
D It acts as a donor and produces n-type material
Answer: D. It acts as a donor and produces n-type material. Phosphorus has five valence electrons; in silicon it can donate an extra electron, giving n-type material.
What happens when boron is added in a small amount to silicon?
A It acts as an acceptor and produces p-type material
B It acts as a donor and produces n-type material
C It makes each silicon atom lose all four bonds
D It makes a metal alloy
Answer: A. It acts as an acceptor and produces p-type material. Boron has three valence electrons, one fewer than silicon, so it creates acceptor states and holes.
Does n-type semiconductor material carry a net negative electric charge overall?
A Yes; it is negatively charged by one electron per atom
B No; it remains electrically neutral, though electrons are majority carriers
C Yes; the donor atoms leave the crystal
D No; it contains no charge carriers
Answer: B. No; it remains electrically neutral, though electrons are majority carriers. The added donor electrons are balanced by positively charged ionized donor atoms, so the crystal remains neutral overall.
Which impurity group is commonly used to create n-type silicon?
A Group 13
B Group 18
C Group 15
D Group 2
Answer: C. Group 15. Pentavalent group-15 impurities act as donors in silicon.
Which impurity group is commonly used to create p-type silicon?
A Group 15
B Group 18
C Group 1
D Group 13
Answer: D. Group 13. Trivalent group-13 impurities act as acceptors and produce holes in silicon.
Which carrier relationship describes an intrinsic semiconductor at thermal equilibrium?
A Electron concentration equals hole concentration
B Electron concentration is zero
C Hole concentration is zero
D Electron concentration is always ten times hole concentration
Answer: A. Electron concentration equals hole concentration. Thermal generation creates electrons and holes in pairs in an intrinsic semiconductor.
Where is the donor energy level typically located in an n-type semiconductor?
A Close to the valence band
B Close to the conduction band
C Exactly halfway through the nucleus
D Outside the semiconductor band structure
Answer: B. Close to the conduction band. Donor levels lie just below the conduction band, so donor electrons need little energy to enter it.
Where is the acceptor energy level typically located in a p-type semiconductor?
A Close to the conduction band
B Inside the atomic nucleus
C Close to the valence band
D Far above the conduction band
Answer: C. Close to the valence band. Acceptor levels lie just above the valence band and can accept electrons from it, leaving holes.
What pair is produced when thermal energy breaks a covalent bond in a semiconductor?
A A proton and a neutron
B Two holes and no electron
C A donor ion and a photon only
D A free electron and a hole
Answer: D. A free electron and a hole. A bond electron promoted to a mobile state leaves a vacancy, producing an electron-hole pair.
Which statement about majority carriers is correct?
A Electrons are majority carriers in n-type and holes in p-type material
B Holes are majority carriers in n-type and electrons in p-type material
C Electrons are the only carriers in both types
D Neither type has majority carriers
Answer: A. Electrons are majority carriers in n-type and holes in p-type material. Donors make electrons dominant in n-type material; acceptors make holes dominant in p-type material.
What does forward bias do to the potential barrier of a p-n junction?
A It increases the barrier without limit
B It reduces the barrier
C It removes all dopant atoms
D It changes the junction into an open circuit
Answer: B. It reduces the barrier. The applied forward voltage opposes the built-in potential and lowers the barrier.
What is the usual current through a reverse-biased diode below breakdown?
A A very large current limited only by the diode wire
B Exactly the forward current
C A small reverse saturation current
D No current under any conditions
Answer: C. A small reverse saturation current. A small reverse current due mainly to minority carriers flows below breakdown.
What happens to the depletion region width when a p-n junction is reverse biased more strongly?
A It decreases to zero
B It stays fixed for every voltage
C It changes into a metal layer
D It increases
Answer: D. It increases. Reverse bias pulls majority carriers away from the junction and widens the depletion region.
What is the approximate forward voltage drop of a conducting silicon diode at ordinary current?
A About 0.7 V
B About 0.07 V
C About 7 V
D About 70 V
Answer: A. About 0.7 V. A silicon p-n diode commonly has a forward drop near 0.7 V, depending on current and temperature.
What is the approximate forward voltage drop of a conducting germanium diode at ordinary current?
A About 3.0 V
B About 0.3 V
C About 0.03 V
D About 30 V
Answer: B. About 0.3 V. A germanium diode typically has a forward drop near 0.3 V.
What type of output does a simple diode rectifier produce from AC?
A Perfectly constant DC without filtering
B A sinusoidal output at a higher voltage
C Unidirectional pulsating current
D A signal with no current in either direction
Answer: C. Unidirectional pulsating current. A basic rectifier makes current flow in one direction, but the output still varies with time.
What does a half-wave rectifier do to the input AC waveform?
A It passes both half-cycles unchanged
B It blocks both half-cycles
C It changes every half-cycle into a separate frequency component
D It passes one half-cycle and blocks the other
Answer: D. It passes one half-cycle and blocks the other. A single-diode half-wave rectifier conducts during one polarity and blocks the opposite polarity.
How many diodes are used in a standard bridge full-wave rectifier?
A Four
B One
C Two
D Six
Answer: A. Four. A bridge rectifier uses four diodes arranged so current through the load has the same direction on both half-cycles.
In which operating condition does a Zener diode regulate voltage?
A Forward bias below the knee
B Reverse breakdown
C Reverse bias below breakdown with zero current
D Unbiased equilibrium only
Answer: B. Reverse breakdown. A Zener regulator uses the diode in reverse breakdown, where its voltage changes little over a range of current.
What is the physical origin of light from an LED?
A A metal filament is heated until it glows
B Photons split into electrons in the junction
C Electron-hole recombination releases photons
D The diode emits neutrons
Answer: C. Electron-hole recombination releases photons. In a forward-biased LED, electron-hole recombination releases energy as photons.
Why is a photodiode useful for sensing light?
A Its forward voltage is independent of light and current
B It blocks all light-generated carriers
C Its resistance is always zero
D Its reverse current changes when incident light creates carriers
Answer: D. Its reverse current changes when incident light creates carriers. Incident light creates electron-hole pairs; under reverse bias these carriers contribute to a measurable photocurrent.
How does a solar cell normally produce electrical output?
A Light creates carriers separated by the junction field, producing voltage and current
B A battery inside the cell supplies the output
C It must be heated until it glows
D It converts current into incident light
Answer: A. Light creates carriers separated by the junction field, producing voltage and current. The built-in field of its junction separates light-generated carriers and can drive current through an external circuit.
What is the output of a NOT gate when its input is 1?
A 1
B 0
C It alternates between 0 and 1
D It is undefined for a digital gate
Answer: B. 0. A NOT gate outputs the logical complement of its input, so input 1 gives output 0.