Difficulty: Easy & Basic
A class has frequency 20 and width 5. What is its frequency density?
A 5
B 4
C 20
D 25
Answer: B. 4. Frequency density is 20 divided by 5, which equals 4.
A class has frequency 30 and width 10. What is its frequency density?
A 10
B 20
C 3
D 30
Answer: C. 3. Frequency density equals the frequency divided by class width: 30 divided by 10.
A histogram class spans 10β20. What is its midpoint?
A 10
B 20
C 30
D 15
Answer: D. 15. The midpoint is the average of 10 and 20, or 15.
A frequency polygon plots classes using which x-values?
A Class midpoints
B Class frequencies
C Cumulative percentages
D Axis label numbers
Answer: A. Class midpoints. Class midpoints represent the centres of grouped intervals on the horizontal axis.
An ogive reaches cumulative frequency 40 at value 50. What does this show?
A 50 observations are below 40
B 40 observations are below 50
C 40 classes end at 50
D The sample total is 50
Answer: B. 40 observations are below 50. A less-than ogive shows the cumulative count below the corresponding upper value.
A sample has 100 observations. What cumulative frequency marks its median?
A 25
B 75
C 50
D 100
Answer: C. 50. The median divides the data into two halves, so its cumulative position is 100 divided by two.
Two histogram classes have equal frequency but widths 5 and 10. Which has greater density?
A The width-ten class
B Both have equal density
C Neither has a frequency
D The width-five class
Answer: D. The width-five class. With equal frequency, the narrower interval has the higher frequency density.
A frequency of 24 occurs in width 6. What is the density?
A 4
B 6
C 18
D 30
Answer: A. 4. Divide 24 by 6 to obtain frequency density 4.
Which graph should show a cumulative total?
A Histogram
B Ogive
C Simple bar chart
D Pie diagram
Answer: B. Ogive. An ogive plots cumulative frequencies across class boundaries.
What should a less-than ogive plot on its x-axis?
A Class frequencies only
B Time-series labels
C Upper class boundaries
D Pie-sector angles
Answer: C. Upper class boundaries. Less-than cumulative frequencies are plotted against successive upper class boundaries.
What should a more-than ogive plot on its x-axis?
A Upper boundaries only
B Class midpoints only
C Line-graph dates
D Lower class boundaries
Answer: D. Lower class boundaries. A more-than ogive uses the lower boundaries for cumulative counts above each point.
Why does a histogram have touching bars?
A Its intervals represent continuous values
B Its values are categories only
C Its classes overlap intentionally
D Its frequencies are cumulative
Answer: A. Its intervals represent continuous values. Adjacent class intervals on a continuous scale share boundaries.
What does a frequency polygon’s vertical axis show?
A Class midpoint
B Frequency or density
C Time period only
D Sector angle
Answer: B. Frequency or density. The vertical axis shows frequency, or frequency density when widths differ.
Why add zero-frequency end points to a polygon?
A To change the class total
B To create a cumulative curve
C Close it toward the axis
D To show a pie chart
Answer: C. Close it toward the axis. End points at adjacent midpoints with zero frequency can close the polygon to the horizontal axis.
Which graph is best for yearly population values?
A Histogram
B Pie chart
C Frequency polygon
D Time-series line graph
Answer: D. Time-series line graph. A line graph displays how a measure changes over successive years.
A line graph rises from 20 to 27. What is the increase?
A 7
B 20
C 27
D 47
Answer: A. 7. The increase is 27 minus 20, which equals 7.
An ogive uses a total of 80. What cumulative position is the median?
A 20
B 40
C 60
D 80
Answer: B. 40. The median is at half the total frequency: 80 divided by two equals 40.
A class has frequency 18 and width 3. What is density?
A 3
B 15
C 6
D 21
Answer: C. 6. Frequency density is 18 divided by 3, or 6.
What does a histogram’s total area represent?
A Number of class intervals
B Class midpoint sum
C Time period length
D Total frequency
Answer: D. Total frequency. When heights are scaled appropriately, the total histogram area represents total frequency.
Why use density on unequal-width classes?
A To preserve area proportionality
B To make all widths equal
C To remove class boundaries
D To convert values into dates
Answer: A. To preserve area proportionality. Density adjusts bar height so the area, not just height, represents class frequency.
A time series has values 5, 8, 6. What happens after the second point?
A The value rises
B The value falls
C It stays unchanged
D The series ends
Answer: B. The value falls. The value decreases from 8 to 6.
Which graph displays cumulative frequency against boundaries?
A Frequency polygon
B Histogram
C Ogive
D Pie diagram
Answer: C. Ogive. An ogive graphs cumulative frequency against class boundaries.
Why should class boundaries be shown on a histogram?
A To label time periods
B To show category colours
C To set pie angles
D To define the interval spans
Answer: D. To define the interval spans. Class boundaries identify the continuous ranges represented by each bar.
Which scale is suitable for plotting yearly values?
A Even time spacing
B Unequal date spacing without reason
C A scale with no labels
D A scale that changes yearly
Answer: A. Even time spacing. Consistent spacing reflects equal time intervals and supports fair comparison.
What should be checked before drawing a graph?
A Only the chart colour
B Data, units, and scale
C Only the axis font
D Only the title length
Answer: B. Data, units, and scale. Checking values, units, intervals, and scales helps avoid inaccurate graphs.