Difficulty: Easy & Basic
What assembly groups multiple battery cells?
A Battery module
B Traction inverter
C Charge port
D Axle differential
Answer: A. Battery module. A module packages several cells into one unit. Modules are combined into the vehicle battery pack.
In pack design, modules combine to form what?
A Drive shaft
B Brake circuit
C Fuel rail
D Traction battery pack
Answer: D. Traction battery pack. The traction battery pack integrates modules with electrical and structural components.
SOC estimates what battery condition?
A Cell strength
B Motor speed
C Pack temperature
D Remaining charge
Answer: D. Remaining charge. State of charge estimates the energy or charge remaining in the battery.
SOH compares a battery with what reference?
A Motor rating
B Road load
C New condition
D Charger voltage
Answer: C. New condition. State of health describes battery condition relative to its original or specified condition.
Stored battery energy is commonly rated in which unit?
A kWh
B kW
C rpm
D bar
Answer: A. kWh. Kilowatt-hours measure energy capacity; kilowatts measure power.
Connecting cells in series mainly increases what?
A Tyre grip
B Cooling flow
C Motor pole count
D Pack voltage
Answer: D. Pack voltage. Series cell voltages add, raising the battery string voltage.
Parallel cell strings mainly increase which rating?
A Pack voltage
B Gear ratio
C Ampere-hour capacity
D Wheelbase
Answer: C. Ampere-hour capacity. Parallel strings increase ampere-hour capacity and current capability when matched cells are used.
Which measurements does a BMS track across cells?
A Speed, torque, yaw
B Fuel, oil, coolant
C Pressure, flow, vacuum
D Voltage, current, temperature
Answer: D. Voltage, current, temperature. Battery management systems monitor electrical and thermal measurements to supervise the pack.
Cell balancing primarily reduces what?
A Motor vibration
B Tyre temperature
C Cell voltage differences
D Cable inductance
Answer: C. Cell voltage differences. Balancing limits differences among cell states so one cell does not reach a limit too early.
When cells overheat, a BMS may reduce what?
A Wheel alignment
B Brake-fluid pressure
C Charge or discharge current
D Steering ratio
Answer: C. Charge or discharge current. Battery controls can restrict current when temperature exceeds operating limits.
A pack fuse interrupts which condition?
A Low tyre pressure
B High motor speed
C Weak radio signal
D Excessive current
Answer: D. Excessive current. A fuse opens a circuit when current exceeds its designed limit.
Pack contactors switch which connection?
A High-voltage battery circuit
B Seat-belt circuit
C Washer-fluid circuit
D Cabin filter duct
Answer: A. High-voltage battery circuit. Contactors connect or isolate the high-voltage battery from vehicle circuits.
For workshop isolation, technicians use which device?
A Service disconnect
B Charge timer
C Reduction gear
D Brake booster
Answer: A. Service disconnect. A service disconnect provides a means to separate the high-voltage battery circuit for service procedures.
DC fast charging supplies the battery with what?
A Hydraulic pressure
B Compressed air
C Direct current
D Mechanical torque
Answer: C. Direct current. Off-board DC fast chargers deliver direct current to the battery under vehicle control.
Near full charge, rapid-charging power often does what?
A Rises without limit
B Tapers down
C Reverses direction
D Stays exactly constant
Answer: B. Tapers down. Charging power commonly tapers at higher state of charge to respect battery limits.
Before a rapid charge, battery preconditioning mainly adjusts what?
A Tyre pressure
B Pack temperature
C Gear backlash
D Brake-pad thickness
Answer: B. Pack temperature. Preconditioning can bring the battery closer to a temperature range that supports faster charging.
Why can a cold battery accept charge more slowly?
A Cell voltage disappears
B Electrochemical processes slow
C The pack loses mass
D The motor turns backward
Answer: B. Electrochemical processes slow. Low temperatures reduce charge acceptance and can increase battery stress if charging is too aggressive.
Depth of discharge describes what fraction?
A Capacity already used
B Motor power available
C Cable length installed
D Wheel torque delivered
Answer: A. Capacity already used. Depth of discharge expresses how much of the battery capacity has been discharged.
One equivalent full cycle represents approximately what?
A One hour parked
B One charger connection
C One motor revolution
D One rated capacity discharged
Answer: D. One rated capacity discharged. Equivalent cycles sum partial discharges until their total is about one rated battery capacity.
Prolonged high battery temperature can accelerate what?
A Tyre balancing
B Battery aging
C Gear synchronization
D Cabin filtration
Answer: B. Battery aging. Elevated temperature can accelerate battery degradation, although the rate depends on chemistry and conditions.
Why is usable battery capacity below gross capacity?
A Cells contain no energy
B Protective reserves remain
C The motor uses petrol
D Charging requires water
Answer: B. Protective reserves remain. Manufacturers reserve energy at the upper and lower ends to support durability and safe operation.
A cell C-rate relates current to which value?
A Rated ampere-hours
B Vehicle mass
C Motor speed
D Coolant volume
Answer: A. Rated ampere-hours. C-rate compares charge or discharge current with the cell capacity in ampere-hours.
Gravimetric energy density compares energy with what?
A Battery mass
B Pack voltage
C Motor torque
D Charging time
Answer: A. Battery mass. Gravimetric energy density is energy stored per unit mass.
Under heavy load, cell internal resistance causes what?
A Voltage doubling
B Zero current
C Voltage drop
D Instant full charge
Answer: C. Voltage drop. Current through internal resistance produces a voltage drop and heat inside the cell.
A battery cooling loop removes what from cells?
A Stored charge
B Excess heat
C Cell voltage
D Motor torque
Answer: B. Excess heat. Thermal management removes heat to keep cells within their designed temperature range.